10pcs 2.4G DL-LN33 Wireless Networking Board UART Serial Port Module CC2530
Shipping:Standard Shipping about 10-25 business days
3:Working frequency:2400~2450MHz (16 channels total)
4:Communication Interface:UART serial port (supports 13 baud rates, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200, 230400, 125000, 250000, 500000)
5:Self-organizing network hops
6:Single hop transmission distance:70 meters (out of the air, no occlusion test)
7:Number of points that can be accommodated:The typical value is 190. When the network tends to be dense, the number of nodes decreases, and the minimum value is 96.
8:MAX packet length:63Byte (including port address information)
9:Transmission capacity:The transmission rate is higher when only one node sends data
Because the routing information of the transmitted packet occupies a certain bandwidth, the longer the length of each packet, the higher the transmission efficiency.
2400 Bit/s when each package contains 3 bytes of data.
10KBit/s when each package contains 30 bytes of data.
13:MAX send rate:250KBit/s
14:Packet retransmission times:Up to 15 times, at least 5 times when the network load is high
15:Air delay:Single-hop between nodes, less than 10mS
16:Transmit power:4. 5dBm
17:Operating Voltage:2. 5V~3. 6V
18:Working current:Less than 30mA
19:Antenna interface:PCB antenna
Pin name:Pin position:Significance
NoUsed:1, 2,10,11,13:Not used, please keep it empty (empty refers to not connected to any circuit)
TestMode:3:Test mode, when working in normal mode in empty, grounding works in test mode. Please use it empty when the user is using it.
TestTx:4:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
TestRx:5:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
BaudReset:12:If this pin is grounded first and then the module is started, the module will force a 115200 default baud rate to operate. In this mode, the baud rate of the module can be read or set. The baud rate read is the baud rate previously set by the module, not 115200. If the baud rate setting is not performed, the module will be restarted again. Work with the previously set baud rate.
Tx:14:Uart output of the module
Rx:15:Uart input of the module
10 x Wireless Networking Board
Customers Also Viewed
10pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boards$34.17Smart ModuleAdd to cart
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThe kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote …
OPEN-SMART Dot Matrix LED 8×8 Seamless Cascadable Red LED Dot Matrix F5 Display Module$10.92Display ScreenAdd to cart
Description This is a 8 x 8 LED dot matrix display module that can be used to display characters and graphics and it is simple to control it. Features – Compatibility:Compatible with UNO R3 / Mega2560. – Libraries for:Max72xxPanel and Adafruit_GFX – Resolution:8 x 8 – Driver – LED color:Highlight Red – Display size:32*32mm – …
5pcs Smart Electronics CD74HC4067 16-Channel Analog Digital Multiplexer PCB Board Module Geekcreit for Arduino – products that work with official Arduino boards$8.53Other Module BoardAdd to cart
Specifications1.2V to 6V operation 2.“On Inch resistance:70 Ohms @ 4.5V 3.6ns break-before-make @ 4.5V 4.Wide operating temperature range:-50→ to 125→Features– This is a pcb board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.– This chip is like a rotary switch – it internally routes the common pinto one of 16 channel pins (CHANxx).– It works …
RIDEN DP50V15A DPS5015 Programmable Power Supply Module with integrated Volt Meterr Ammeter$121.32Power Supply ModuleAdd to cart
DescriptionThis module has power-down stored function and can store 10 groups preset value. And it also has the function of extracting quickly two groups stored value.Compared with the traditional analog power supply, it is more convenient to quickly extract the voltage or current required. LCD display on the module has the function digital voltmeter and …
20Pcs Serial Port WIFI ESP8266 Module Adapter Plate with IO Lead Out for ESP-07 ESP-08 ESP-12$12.02Smart ModuleAdd to cart
20Pcs Serial Port WIFI ESP8266 Module Adapter Plate With IO Lead Out For ESP-07 ESP-08 ESP-12This Adapter Plate is for ESP-07 ESP-08 ESP-12, a test board with IO lead out.NoteNeed to solder 3V regulator by youself.ESP-07, ESP-08, ESP-12 module board are not included!!!Package included20 x Serial Port WIFI ESP8266 Module Adapter Plate40 x Pins
KING PIGEON M240T PT100 4RTD+1RS485 +1RJ45 4-way thermal Resistance PT100 Temperature industrial Ethernet IO Remote Collection Module$165.20Network ModuleAdd to cart
Note:Please refer to the title for the actual supported functions.This M240T version:Support PT100 4RTD+1RS485 +1RJ45 PT100DocumentsManual:Click here to openTool:Click here to openIntroductionThe M240T Ethernet Remote I/O Module is an industrial class, isolated designed, high reliability, high stability and high precision data acquisition module, embedded 32-Bit High Performance Microprocessor MCU, Integrated 1 Industrial 10/100M adaptive Ethernet …