EQKIT Audio Spectrum 8×4 DIY Kit Level indicator Voice Spectrum Lights Red+Blue Colorful Display
$11.74
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
This is a kit parts. You should solder it by yourself.
Features
1. High sensitivity;
2. Low power;
3. Wide operating voltage range;
4. Low power consumption;
5. DIY design;
6. Colorful display;
7. Mode adjustable;
Parameter
No.:Parameter:Value
1:Model:ASD-84
2:Standby current:Less than 1mA
3:Soldering difficulty Level:Easy
4:Working voltage:DC 5V
5:Display LED:8*4
6:Display color:Red+Blue
7:LED Size:2*5*7
6:PCB Size:94*39.5mm
Instructions
Step 1:Complete the installation in the normal way following installation manual and schematic. (Please request separately).
Step 2:Connect audio;
Step 3:DC 4-9V voltage;
Step 4:Adjust the working mode
Step 5:Test and use.
Mode setting
Mode:Set Method:Remarks
Factory Testing Mode:Press button S1 before Power on:It is used to detect all LED whether can be ON
Fast Flashing Mode(3):Short press S1 less than 1second:The refresh frequency is very fast
Medium Flashing Mode(2):Short press S1 less than 1second:The refresh frequency is general
Slow Flashing Mode(1):Short press S1 less than 1second:The refresh frequency is slow
High Sensitivity Mode(H):Long press S1 more than 2second:It can detect weaker audio signals
Medium Sensitivity Mode(B):Long press S1 more than 2second:It can detect general audio signals
Low Sensitivity Mode(L):Long press S1 more than 2second:It can filter more interference audio signals
Using attention
1. Please make sure all the components in the right direction and right place.
2. Please check whether pseudo/float welding. This is very important.
3. The soldering iron can’t touch the components for a long time, otherwise, the components will be damaged because of the high temperature.
4. It is recommended to use a stable power supply, otherwise, it may interfere with the audio signal output.
Component list
NO.:Component Name:PCB Marker:Parameter:Quantity
1:Metal Film Resistor:R15:10ohm:1
2:Metal Film Resistor:RX1-RX4,RY5-RY12:47ohm:12
3:Metal Film Resistor:R13-R14:470K:2
4:Ceramic Capacitor:C5:0.001uF 102:1
5:Ceramic Capacitor:C2-C4:0.1uF 104:3
6:Electrolytic Capacitor:C1:220uF:1
7:Red LED:D1-D16:2*5*7mm:16
8:Blue LED:D17-D32:2*5*7mm:16
9:Audio Socket:J2,J3:SMD3P:2
10:Power Socket:J1:DC3.5:1
11:WD1084:U1:DIP-16:1
12:Button:S1:6*6*5:1
13:USB to DC Cable::100cm:1
14:Audio Cable::100cm:1
15:PCB:ASD-84:94*39.5mm:1
Application
1. Electronic teaching
2. Exercise soldering skills
3. Circuit application
Frequency asked questions
1. Why can’t work
A:Please make sure all components in the right direction and right place and check whether pseudo/float welding. This is very important.
Install tools you need preliminary preparation by yourself
1>. Soldering iron;
2>. Multimeter;
3>. Solder wire;
4>. Iron stand;
5>. Diagonal cutting pliers;
6>. The screwdriver;
7>. Tweezers;
8>. Long nose pliers;
9>. Suction tin;
10>. Cleaning sponge;
11>. Screwdriver set.
Package included
1 x EQKIT® Audio Spectrum 8×4 DIY Kit
Weight | 0.049 kg |
---|
Customers Also Viewed
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water Heater
$21.87Laboratory Heating EquipmentsAdd to cartDC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterSpecificationsModel:SSG-2Type:Normally ClosedMaterials:Plastic & CopperDimension:83*90*49cmPipe Inside Diameter:1/2 inchNet Weight:(approx.) 190gFeaturesThis is a DC12V solenoid valve usually used for solar water heater.It can work with water from 1 to 100℃ (or some other liquid).Working Voltage Range:Rated Voltage ±10%Working Water Pressure:0.02 to 0.8MpaThe working water pressure would be too low/high to …
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterRead More
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set Kit
$76.17Terminal BlocksAdd to cartDescription650 Pcs Assorted Ring Insulated Electrical Wire Terminals Crimp Connector Set KitSpecificationQuantity:650PcsMaterial:Copper + PVC+ TinplateInsulated crimp terminals.All are enclosed in plastic case for easy access.The assorted crimp terminals is including50 x Ring M3 Red50 x Ring M4 Red50 x Ring M5 Red50 x Ring M6 Red50 x Ring M8 Red50 x Ring M4 Blue50 x …
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set KitRead More
3.5 inch Protective Enclosure Case Support Dispaly Screen or Cooling Fan for Raspberry Pi
$9.26Raspberry Pi & Orange PiAdd to cartFeatures– Fully updated for Raspberry Pi 3B+/3B/2B– Can support 3.5 inch screen or cooling fan (notes:can not assemble them at the same time)– Heat sink openings for both CPU and LAN chip– High-gloss finish, surface mountableSpecificationsColor:BlackMaterial:ABSSuitable for Raspberry Pi 3B+/3B/2BWeight:45gSize:9cm*6.2cm*3.4cmPackage Included1x ABS Case4x Non-slip mat4x Screws
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module for
$47.25DIY Electronic KitsAdd to cartDescription1. Use TM1650 (compatible with AIP650) digital tube driver chip, support 8-level brightness adjustment, working voltage 3.3V ~ 5.5V2. IIC interface, only need 2 ordinary IO can drive, do not need to repeat scanning of MCU, saving MCU resources.3. 4 digit 0.56 inch red common negative digital tube with decimal point.4. 0.56 inch with four …
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module forRead More
WEAH-81 Car Heavy Bass Frequency Divider High and Low 2-way 2 Bass Crossover Upgrade Tool
$33.09Amplifier BoardAdd to cartFeatureBrand:WEAHModel:81Power:100WApplicable impedance:4-8ohmFrequency response:100Hz ~ 45HzDimensions:133 x 95 x 44mmApplication environment:Car or home speaker DIYPackage includes1 x Bass Frequency DividerHow to Wire:
5pcs 8-36W intelligent Sensor LED Ceiling Light And Sound Control Power Supply Module Bulb Panel Light Built-in Power Driver
$21.42Power Supply ModuleAdd to cartDescriptionInput Voltage:AC185-265VOutput Current:0.22AOutput Voltage:24-108VEfficiency:90%Working Frequency:50/60HZOutput Power:8-24WSound Control:50-75dBLight control:7-20LuxDiameter:25.8mmFeature1. The combination of sound and light control, when the light is strong, does not work, the light intensity is lower than 12-15LUX, and the sound of the induction 27-36DB starts automatically.2. Delay 40-60S automatically extinguished, easy to install, compatible with ordinary switches, no additional wiring.3. Single trigger, …
Reviews
There are no reviews yet.