Geekcreit DIY Full Color Rotating POV LED Hand Spinner Electronic Kit
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
This DIY full color rotating POV LED electronic kit using seven RGB Led designed, combined to the high-speed 608 rotation bearing,
it can spinning on the desktop or between the fingertips when rotating the side of the kit, and shows the different color of the pattern.
the pattern can be change automatically. it also has the ON/OFF function by one button. this is a very interesting and easy SMD
learning DIY kit for the beginner.
Manual is Here!
Features
Using 5050 RGB Led to Display;
18 kinds of different color changing pattern;
Using the High-speed 608 Rotation Bearing, it can rotate for more than one minute;
Power Supply:2x3V CR2032(NOT Included);
One button ON/OFF Power function;
Auto Power Off in 5 minutes without Operation;
PCB and Acrylic Size:115mm x 30mm;
Finished Product Size:115mm x 30mm x13mm;
Function
1. Insert two CR2032 batteries and press the button to power on.
2. It can spinning on the desktop or between the fingertips when rotating the side of the kit,
and shows the different color of the pattern.
3. Press the button again or without operation after 5 minutes to power off.
Package included
1 x Geekcreit® DIY Full Color Rotating POV LED Hand Spinner Electronic Kit
| Weight | 0.037 kg |
|---|
Related products
DIY CD4060 SMD Music LED Light Kit Electronic Experimental Training Teaching
$8.13DIY Electronic KitsAdd to cartWorking principleUsing the SMD CD4060 control 12 red, yellow and green LED flashing, adjust RP1 can change the speed of flashing, while the music chip issued a wonderful music. The kit uses SMD components and plug-in components, is ideal for practical training requirements.The CD4060 consists of an oscillator and a 14-bit binary serial counter bit. …
DIY CD4060 SMD Music LED Light Kit Electronic Experimental Training TeachingRead More
10Pcs DIY Touch Vibration Alarm Kit Electronic Training Teaching
$34.22DIY Electronic KitsAdd to cartWorking principleThe touching vibration alarm consists of touch trigger circuit, vibration trigger circuit and alarm circuit. The 555 time base circuit U1 forms the typical monostable operating mode. The transient time is determined by the values of RP1, R2 and C2.Usually the circuit is in steady state, 555 time base circuit 3 pin output low, …
10Pcs DIY Touch Vibration Alarm Kit Electronic Training TeachingRead More
MINI 0.96 inch OLED ATU100 Automatic Antenna Tuner 100W Automatic Daytime Tuning Kit
$58.71DIY Electronic KitsAdd to cartThe main features of ATU-100 MINI 7×7 auto-tuner antennaAt 1.8-50 MHzAllowable power supply voltage range when operating at a frequency of 10-15V DCMaximum current consumption:300 mAMaximum working power:100 WMaximum possible power:150 W1 watt:you need to start setting the minimum powerMinimum possible power:0.1 WMeasurement procedure for power up to 10W:0.1WPowerful measurement step, 10 W higher than …
MINI 0.96 inch OLED ATU100 Automatic Antenna Tuner 100W Automatic Daytime Tuning KitRead More
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.