3pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$10.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
3 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.081 kg |
---|
Customers Also Viewed
3pcs 2x50W TPA3116 AUX+Bluetooth 5.0 HIFI High Power Digital Amplifier Stereo Board AMP Amplificador Home theater without Shell
$54.90Amplifier BoardAdd to cartSpecificationsAudio input:AUX+bluetoothWork voltage:9-24 DCPower:2*50WCooling fin:LargeSpeaker:4-8Ω;30-200WProtection:Overvoltage,undervoltageSize:84*52*24mmFeatures1. This product is full of materials, featuring high performance and high performance price, especially for HIFI music power amplifier with high power and high fidelity.2. TPA3116D2 is a type D amplifier IC launched by TI company, which has very high index parameters.The maximum modulation frequency is 1.2MHZ, and the high …
5PCS USB To TTL Debug Serial Port Cable for Raspberry Pi 3B 2B / COM Port
$20.44Raspberry Pi & Orange PiAdd to cartMore info and driver, please !!!Supports WIN XP/WIN7/ WIN8/ WIN10Reference to WIN10, you can !!!NoteNo driver on raspberry pi 3 model bRaspberry Pi main board is not included!Package included5x USB To TTL Debug Serial Port Cable For Raspberry Pi / COM Port
DIY LED Light Kit ONLY for LEGO 60197 Passenger Train Building Block Bricks Lighting
$32.79DIY Electronic KitsAdd to cartSpecificationInterface:USBColor:As the picture shownThe product is just a light kit, not included the model!!!FitmentONLY For LEGO 60197 Passenger Train Building Block Bricks ToyFeaturesEasy to install.LED powered by USB.Make your model more cool.Package Included1 x LED Light Kit(Model Not Included)
5Pcs M5Stack I/O Hub 1 to 6 Expansion Board Grove I/O interface for Blockly Development IoT MEGA328 Module for Arduino
$75.21Converter BoardAdd to cartDescriptionPbHUB, is a expander for singel-bus GROVE PORTB(Black port on M5GO Base). 1-to-6. PortB can be used as GPIO and analog in two data lines connected to GPIO36 and GPIO26 on ESP32. Same as PaHUB, it provides a solution for mutiple device control by PORTB. With PbHUB each of the IO can be configurated to …
10Pcs Green LED Power Symbol Momentary Latching Switch LED Light Push Button SPST
$20.86Electronic Accessories & SuppliesAdd to cart10Pcs Green LED Power Symbol Momentary Latching Switch LED Light Push Button SPSTDecriptionLatching type:Push it– on, push it again — offLED color:GreenSize(H*D):1.4 x 1cm / 0.55inch x 0.39inch (approx)Quantity:10 pcsFunction:MomentaryLED light voltage:3.2VSwitch voltage:12VMaximum operating current:20mAWith led light, with power symbol, light touch switchEasy to use and installNote1. Please check the picture and part number carefully …
10Pcs Green LED Power Symbol Momentary Latching Switch LED Light Push Button SPSTRead More
100Pcs Red Heat Shrink Solder Sleeve Seal Wire Splice Butt Connector AWG 22-18GA
$72.89ConnectorsAdd to cartName:(100) Heat Shrink Solder Sleeve Seal Wire Splice Butt Connector AWG 22-18GA RedMaterial:Tinned CopperColor:RedShrinking Ratio:2:1Working temperature:-55℃~125℃Shrink temperature:80℃Solder melting temperature:138℃Complete solder melting temperature:160℃Cable cross-section:0.5mm-1.0 mmDiameter:3mm/0.12inch(appr.)FeaturesPlacement on Vehicle:Left, Right, Front, Rear.Solder and seal and with advanced waterproof function.Polyolefin tubing in outside and hot melt adhesive in inside.Can be ideal used in marine and automobile applications.Improve pullout strength, …
100Pcs Red Heat Shrink Solder Sleeve Seal Wire Splice Butt Connector AWG 22-18GARead More
Reviews
There are no reviews yet.