3pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$10.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
3 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.081 kg |
---|
Customers Also Viewed
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire Connectors
$70.86ConnectorsAdd to cartSpecificationModel:SC6-6~SC35-10Material:Tin Plated CopperColor:SilverSize:6mm²/10mm²/16mm²/25mm²/35mm²Mount Hole:6 mm/8 mm/10 mmBox Size(L*W*H):280 x 126 x 14 mmQuantity:100 PcsFeaturesElectro-plated tin exterior.Premium quality copper material, environmentally friendly, safe for using.These tube lugs have a bell shaped end allowing for easy insertion of the cable.Acceptable working temperature is -55℃ to 100℃ and are suitable for applications in the Australian Climate.Copper lugs are …
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire ConnectorsRead More
TDA7377 Subwoofer Amplifier Audio Board 38Wx3 Mini Home Amp 2.1 Channel HiFi Stereo Power Amplifier DIY
$21.86Amplifier BoardAdd to cartDescriptionThe power amplifier board uses 7377 amplifier chip, dual circuit design, optional DC12V / AC12V power supply, and uses 2.1 three-channel output. Available for Bluetooth / Wireless Microphone / Fan. Separate design, easy installation, provides volume and subwoofer adjustment. ParametersWorking voltage:DC12V / AC12V Chip:TDA7377 Op amp:LT084 / 324 Working voltage:DC12V / AC12V Output power:38Wx3 Channel …
XH-W1411 220V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$17.48Test & Measuring ModuleAdd to cartSpecificationsTemperature range:-55- + 120→Temperature measurement accuracy:± 0.3→Resolution:0.1→Temperature range:-19 ~ 99→Control accuracy:1→Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probeSupply voltage:220VTemperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)Output Type:10A relay outputsSize:90*60mm/3.54 Inch*2.36 InchHole size:70*50mm/2.76 Inch*1.96 InchFeatures– The board and plastic panels fixed column compartment and lock nut– Connect the power supply according to the drawings …
3Pcs HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
$24.99DIY Electronic KitsAdd to cartDescriptionIt is DIY Kit, must be assemble to work. User need technical operation ability.Package included3 x HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpa
$60.74Carbon FiberAdd to cartSpecificationSize;100 x 100cmWidth; 0.25mmMaterial:Carbon fiberCompressive strength:3900 mpaFeaturesa.Uniform texture, without color. Weaving skills, good gloss.b.Mainly used in aircraft main, tail and body; automotive engine synchronizer, hood, bumpers, decorative pieces; bike frame, wheels, leading; racket, cone; kayaking, snowboarding; various models, helmets , watches, pens, bags.Main purpose1. Aerospace:fuselage, rudder, rocket engine shells, missiles casual flow, such as solar …
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpaRead More
3pcs EQKIT 60 Seconds Electronic Timer Kit DIY Parts Soldering Practice Board
$28.54DIY Electronic KitsAdd to cartInstruction:http://img.staticbg.com/file/products/20180726215941ETI-60-timer-kit.pdfFeatureOperating voltage:DC5VStandby current:≤8mAWorking current:≤10mACountdown:60 secondsCountdown ends prompt:three alarmsSoludering difficulty:GeneralBoard size:84 x 84mmNote:Electronic production kit, require buyer soldering assembly.Package included3 x Electronic Timer K
Reviews
There are no reviews yet.