20pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$54.99
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
20 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.54 kg |
---|
Customers Also Viewed
Solar Powered Floating Bird Bath Water Fountain Pump Pond Pool Water Pump
$42.51Electrical Pump & ValveAdd to cartDescriptionThis product is solar-powered decorative fountain.It is made up of highly efficient solar panel and new brushless pump.IT is start-up fast,efficient and strong stability.In addition,it has no electric outlet or external battery,so it’s not only easy to use,but also safe.This product is suitable for bird bath,fish tank,small pond,garden decoration,water circulation for oxygen,etc.FeatureSolar panel:7V/1.4WBrushless pump input:DC4.5-10VMaximum …
Solar Powered Floating Bird Bath Water Fountain Pump Pond Pool Water PumpRead More
Vibration Switch Sensor Module Vibration Sensor Alarm Module Smart Car Accessories
$4.36Sensor & Detector ModuleAdd to cartFeatures 1. Onboard LM393 voltage comparator chip and vibration sensing probe2. Support 5V/3.3V voltage input3. Onboard signal output indication, the output valid signal is low level and the indicator light is on, the output signal can be directly connected with the single chip IO4. The sensitivity of signal detection can be adjusted5. With 3mm screw …
Vibration Switch Sensor Module Vibration Sensor Alarm Module Smart Car AccessoriesRead More
TPA3116 Dual Channel 50Wx2 Digital Amplifier Board
$23.15Amplifier BoardAdd to cartSpecificationPower amplifier chip:TPA3116Power supply voltage:11 ~ 26VDC DC input with limit reverse polarity protection(Recommended DC 24V current 3A and above switching power supply)Output power:stereo 50W + 50W, PBTL monaural 100WLoad impedance:4 to 8 ohms (horn speaker impedance)Audio input:2.54mm3 pin seatPackage Included1 x Digital Amplifier Board
5pcs Geekcreit 3 in 1 AC 60-500V 100A Square Yellow LED Digital Voltmeter Ammeter Hertz Meter Signal Lights Voltage Current Frequency Combo Meter indicator Tester with Round CT
$48.24Electronic Accessories & SuppliesAdd to cartDescriptionDisplay:Voltage, current, frequencyDisplay color:YellowMeasuring voltage range:60~500V AMeasuring current range:6~100AMeasuring frequency range:20-70HzSize:2.8*5cm/1.10inch*1.97inch (D*H)Note:Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!Package included5 x 22MM Indicator5 x Round CT
5pcs Nano V3.0 Terminal Adapter AVR ATMEGA328P without NRF2401+ Expansion interface DC Power Board
$38.18Expansion Board & ShieldAdd to cartFeature1. The item is a terminal expansion adapter, working very well for prototyping Nano projects2. There are pins expansion hole for the NANO board, which can directly lead the pins; With DC power supply interface, you can directly add external power or battery to supply power3. With NRF2401+ expansion interface, you can insert NRF2401+ to …
Reviews
There are no reviews yet.