10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with Cable
$11.26Sensor & Detector ModuleAdd to cartFeatures– Can receive standard 38KHz remote control signals by means of programming can decode the remote control signals– Strong ability to resist electromagnetic interference and light– Widely used in stereo, TV, set-top boxes, digital photo frame, car stereo, remote control toys, satellite receivers, hard disk players, air conditioner, heater, electric fan, lighting and other home …
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with CableRead More
600V 45A 3 Position Terminal Block Barrier Strip Dual Row Screw Block Covered W/ Removable Clear Plastic insulating Cover
$16.19Terminal BlocksAdd to cartSpecificationModel:TB4503Type:Terminal block Working frequency:High frequencyInterface type:AC/DCRated current:45ARated voltage:600VConductor cross section:0.5-4mm2Number of pin:6Number of bits:3Contact material:IronSize:70mm x 38mm x 24mmFeature:–Moistureproof–High quality guides,durable–High quality thickened conductive parts–High quality iron screw with high strength–Dust proof transparent plastic protective coverPackage Included1 x Terminal block
5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V inverter
$26.31Smart ModuleAdd to cart5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V Inverter For 10 Inch To 22 Inch ScreenFeatureVoltage:10V ~ 28VCable:300mm(L) / 6 pinSize:122 x 27mm ( L x W )Interface:double light small interfaceInterface definition:1. VCC 2. GND 3. NULL 4. NULL 5. ON/OFFPackage included5 x 2 lamp backlight universal laptop LCD CCFL inverter 10V-28V5 x Cable
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier Board
$20.90Amplifier BoardAdd to cartFeatures1. Power filter function is through the power line access power filter,get a specific frequency of the power signal, or eliminate a specific frequency power signal. By using this feature of the power filter, a square wave complex or complex noise passing through the power filter can be converted into a sine wave of a …
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier BoardRead More
5pcs EQKIT TDL-555 Touch Delay LED Light DIY Kit Touch Delay Lamp Electronic Parts Production Kit DC 5V 3s to 130s Adjustable
$10.12DIY Electronic KitsAdd to cartFunction1. Connect Power,Red LED ON2. Touch and then start to delay and Red LED OFF and 5pcs White LED ON at the same time3. Red LED ON and White LED OFF after delay4. Delay can be adjust by potentiometer for 3-130 secondPackage included5 x EQKIT® TDL-555 Touch Delay LED Light DIY Kit
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4
$22.95Raspberry Pi & Orange PiAdd to cartOverviewThis is a universal driver board for e-Paper panels, can be used to drive various SPI interface e-Paper from Waveshare.FeaturesStandard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson NanoSPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.Onboard voltage translator, compatible with 3.3V/5V MCUsComes with development resources and manual (examples …
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4Read More
Reviews
There are no reviews yet.