Micro ATmega32U4 5V 16MHz Development Board
$26.23
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The Micro ATmega32U4-MU is a tiny microcontroller board based on the ATmega32U4. It has 20 digital input/output pins (7 of which can be used as PWM outputs and 12 as analog inputs), a crystal oscillator, a micro-USB connection, an ICSP header and a reset button. With a 16 MHz frequency and 5V operating voltage, this board is similar to the Arduino Leonardo, although the Micro ATmega32U4-MU is more compact (17.78*48.26mm).
The board contains everything needed to support the microcontroller; you just have to connect it to a computer and get started! Its form factor enables it to be easily placed on the circuit board.
Like the Arduino Leonardo, the Micro ATmega32U4-MU has built-in USB connection, eliminating the need for a converter. This allows the Micro to appear to a connected computer as an HID-device, such as a keyboard or mouse, in addition to a COM-port. The board is also able to perform other Arduino Leonardo functions.
Power
The Micro ATmega32U4-MU can be powered via a USB connection.
Power Supply
5V:The regulated power supply used to power the microcontroller and other components on the board. This can come either from VIN via a voltage regulator, or be supplied via USB, or another regulated 5V supply.
3V3:A 3.3V supply generated by the on-board regulator. Maximum current draw is 50mA.
GND:Ground pins.
I/O Pins
Each of the 20 digital pins can be used as an input or output. They operate at 5V. Each pin can provide or receive a maximum of 40 mA, and has an internal pull-up resistor (disconnected by default) of 20-50 k Ohms. In addition, some pins have additional functions
— Serial interface:0(RX) and 1(TX) pins. Used to receive (RX) and transmit (TX) data using the ATmega32U4 hardware serial capability. Note that on the Micro ATmega32U4-MU, the Serial class refers to USB (CDC)-communication, for data transfer on pins 0 and 1, use the Serial1 class.
— TWI:2 (SDA) and 3 (SCL) pins. Support TWI (12C) communication using the Wire library.
— External interrupts:3 (interrupt 0), 2 (interrupt 1), 0 (interrupt 2), 1 (interrupt 3) and 7 (interrupt 4). These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
— PWM:3, 5, 6, 9, 10, 11 and 13. Provide 8 bit PWM output with the analogWrite() function.
— SPI:on the ICSP header. These pins support SPI communication using the SPI library. Note that the SPI pins are not connected to any of the I/O pins as they are on the Arduino Uno. They are only available on the ICSP connector.
— Analog inputs:A0 — A5, A6 — A11 (on digital pins 4, 6, 8, 9, 10 and 12). The Micro ATmega32U4-MU has 12 analog inputs (A0 — A11), all of which can also be used as digital i/o. Analog inputs A0 — A5 appear in the same locations as on the Arduino Uno; inputs A6 — A11 are on digital i/o pins 4, 6, 8, 9, 10 and 12, respectively. Each analog input provide 10 bits of resolution (1024 different values). By default, the analog inputs measure from 0 to 5 volts, though it is possible to change the upper end of their range using the AREF pin and the analog Reference() function.
— Reset. A low signal level resets the microcontroller.
LEDs
* RX and TX — flash when data is being transmitted via USB connection.
* ON — power indicator.
* L — LED connection to digital pin 13.
Memory
The ATmega 32U4 microcontroller has 32 KB memory (with 4 KB used by the bootloader). It also has 2.5 KB SRAM and 1 KB EEPROM (which can be read and written with the EEPROM library).
The Micro ATmega32U4-MU has a number of facilities for communicating with a computer, another Arduino device or microcontrollers.
The ATmega32U4 provides serial UART TTL serial communication, which is available on digital pins 0(RX) and 1(TX).
Having hardware support for USB, the ATmega32U4 also allows for serial communication with the computer over a virtual COM port.
The Micro ATmega32U4-MU also acts as a USB 2.0 device, using standard USB COM drivers. The Arduino software includes a serial monitor that allows simple textual data to be sent to and from the board. Which we will do in the example given under the description.
A SoftwareSerial library allows for serial communication on any of the ATmega32U4-MU’s digital pins.
The ATmega32U4 also supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the 12C bus. The SPI library can be used for SPI communication.
Programming
The board can be programmed with Arduino software, by selecting ATmega32U4 in the Board menu.
The ATmega32U4 microcontroller on the Micro ATmega32U4-MU comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer.
You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header.
Automatic Reset
Rather than requiring a physical press of the reset button before an upload, the Micro ATmega32U4-MU is designed in a way that allows it to be reset by Arduino software running on a connected computer. The reset is triggered when the virtual CDC COM port is opened at 1200 baud and then closed. When this happens, the processor will reset, breaking the USB connection to the computer. After the processor resets, the bootloader starts, remaining active for about 8 seconds. The bootloader can also be initiated by pressing the Reset button. Note that when the board first powers up, it will jump straight to the user sketch, if present, rather than initiating the bootloader.
USB Overcurrent Protection
The Micro ATmega32U4-MU has a resettable polyfuse that protects the computer’s USB ports from shorts and overcurrent. Although most computers have their own internal protection, the fuse provides an extra layer of protection. If more than 500mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.
Microcontroller:ATmega32U4-MU
Power Out:3.3V-180m
5V-800m
Power IN. USB:5V
Power IN. VIN/DC Jack:5V
Power Consumption:5V 220mA
Logic Level:5V
USB:Micro USB
Clock Frequency:16MHz
Operating Supply Voltage:3.3V
Digital I/O:20(7-PWM)
Analog I/O:12
Data RAM Type/Size:2.5Kb
Data ROM Type/Size:1Kb
Interface Type:ISP
Operating temperature:−40㎡°/+85㎡°
PCB size (L*W):48.26*17.78mm
Weight:8.5g
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Package includes
1 x Micro ATmega32U4 5V 16MHz Development Board
Weight | 0.015 kg |
---|
Customers Also Viewed
WEAH-307 3 Way Audio Speaker Crossover 100W Filter Treble Mediant Bass Frequency Divider Module
$15.30Amplifier BoardAdd to cartFeatureMode:WEAH-307Power:100WImpedance:4-8ohmCompatible for:Under 6inches HornTreble Standard:12db/octBass Standard:12db/octSize:8.5×6.2×2.6cmFrequency response:low 45Hz, high 20KHzPackage includes1 x 100W Filter Treble Mediant Bass Frequency Divider
3pcs WXD3-13-2W Precision Potentiometer 22K 22K Ohm Wirewound Multi-Turn Potentiometer
$10.49Module ComponentsAdd to cartSpecificationsResistance range:22K┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included3 x Potentiometer
20Pcs Serial Port WIFI ESP8266 Module Adapter Plate with IO Lead Out for ESP-07 ESP-08 ESP-12
$12.02Smart ModuleAdd to cart20Pcs Serial Port WIFI ESP8266 Module Adapter Plate With IO Lead Out For ESP-07 ESP-08 ESP-12This Adapter Plate is for ESP-07 ESP-08 ESP-12, a test board with IO lead out.NoteNeed to solder 3V regulator by youself.ESP-07, ESP-08, ESP-12 module board are not included!!!Package included20 x Serial Port WIFI ESP8266 Module Adapter Plate40 x Pins
10pcs 2S 5A Li-ion Lithium Battery 7.4V 8.4V 18650 Charger Protection Board BMS for Li-ion Lipo Battery
$16.88Battery Protection ModuleAdd to cartSpecificationsModel:HX-2S-A2 Overcharge voltage range:4.25-4.35v ± 0.05vSize:17.5 * 17.5 * 3.2mm over discharge voltage range:2.5-3.0v ± 0.05vUpper limit operating current:5A Operating temperature:-40 — +50 °Upper limit instantaneous current:7A Storage conditions:-40– +80 °Quiescent current:less than 10uA Effective life:more than 50,000 hoursInternal resistance:less than 300mΩ Short circuit protection:can be protected, need to charge recoveryCharging voltage:8.4V-9VWelding point DescriptionB + …
DC 24V 600L/H Submersible Pump Immersible Pump Under Water Pump Bath Pump
$42.51Electrical Pump & ValveAdd to cartSubmersible Pump Immersible Pump Under Water Aquarium Bath Pump DC 24V 600L/HSpecificationColor:GreyUse:SubmersibleMaterial:Engineering ABSRated Voltage:DC 24VStarting Voltage:6VCurrent:0.75AFlow:600L/HNoise:50dB MAXMax. Head:500cmPower:18wWaterproof grade:IP68Motor:brush motorWater temperature:-20 ° C ~ 60 ° ° CAmbient humidity:45%~90%No load current:less than 0.2ACurrent at load:1.2ACable:1.5m /59.06inch(appr.)Total Length:105.9mm /4.31inch(appr.)FeaturesBrand New and high quality.Suitable for tap water, sea water, ground waterCannot be used directly with 220V AC …
DC 24V 600L/H Submersible Pump Immersible Pump Under Water Pump Bath PumpRead More
TDA7498 2.1 Digital Power Amplifier Board 200W+100W+100W Supasses TPA3116 Class D DC24V
$70.06Amplifier BoardAdd to cartFeatures-Using original TDA7498 TL072-The front input capacitor and the inter-stage coupling capacitor use Siemens’ top-level capacitors 1UF, the electrolytic capacitor signal main circuit uses Taiwanese famous brands, and the main filter capacitor uses special electrolytic capacitors 2≠2200UF to ensure strong continuous power support.-The resistors are high-precision chip resistors, and the main circuit uses five-ring metal …
TDA7498 2.1 Digital Power Amplifier Board 200W+100W+100W Supasses TPA3116 Class D DC24VRead More
3Pcs RobotDyn RTC DS1307 Real Time Clock Battery Shield with Pin Headers Set
$18.67Expansion Board & ShieldAdd to cartPINOUT:http://img.staticbg.com/file/products/20171226001032PINOUT-RTCDS1307.pdfSchematic:http://img.staticbg.com/file/products/20171226001140Schematic-RTCDS1307.pdfFeatureType:Logic ICsPackage includes3 x RTC DS1307 (real time clock) + battery3 x Wemos D1 mini shield6 x Male Pin Header 8pins6 x Female Pin Header -BLACK 8pins6 x Stackable Header – BLACK 8pins
Reviews
There are no reviews yet.