Micro ATmega32U4 5V 16MHz Development Board
$26.23
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The Micro ATmega32U4-MU is a tiny microcontroller board based on the ATmega32U4. It has 20 digital input/output pins (7 of which can be used as PWM outputs and 12 as analog inputs), a crystal oscillator, a micro-USB connection, an ICSP header and a reset button. With a 16 MHz frequency and 5V operating voltage, this board is similar to the Arduino Leonardo, although the Micro ATmega32U4-MU is more compact (17.78*48.26mm).
The board contains everything needed to support the microcontroller; you just have to connect it to a computer and get started! Its form factor enables it to be easily placed on the circuit board.
Like the Arduino Leonardo, the Micro ATmega32U4-MU has built-in USB connection, eliminating the need for a converter. This allows the Micro to appear to a connected computer as an HID-device, such as a keyboard or mouse, in addition to a COM-port. The board is also able to perform other Arduino Leonardo functions.
Power
The Micro ATmega32U4-MU can be powered via a USB connection.
Power Supply
5V:The regulated power supply used to power the microcontroller and other components on the board. This can come either from VIN via a voltage regulator, or be supplied via USB, or another regulated 5V supply.
3V3:A 3.3V supply generated by the on-board regulator. Maximum current draw is 50mA.
GND:Ground pins.
I/O Pins
Each of the 20 digital pins can be used as an input or output. They operate at 5V. Each pin can provide or receive a maximum of 40 mA, and has an internal pull-up resistor (disconnected by default) of 20-50 k Ohms. In addition, some pins have additional functions
— Serial interface:0(RX) and 1(TX) pins. Used to receive (RX) and transmit (TX) data using the ATmega32U4 hardware serial capability. Note that on the Micro ATmega32U4-MU, the Serial class refers to USB (CDC)-communication, for data transfer on pins 0 and 1, use the Serial1 class.
— TWI:2 (SDA) and 3 (SCL) pins. Support TWI (12C) communication using the Wire library.
— External interrupts:3 (interrupt 0), 2 (interrupt 1), 0 (interrupt 2), 1 (interrupt 3) and 7 (interrupt 4). These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
— PWM:3, 5, 6, 9, 10, 11 and 13. Provide 8 bit PWM output with the analogWrite() function.
— SPI:on the ICSP header. These pins support SPI communication using the SPI library. Note that the SPI pins are not connected to any of the I/O pins as they are on the Arduino Uno. They are only available on the ICSP connector.
— Analog inputs:A0 — A5, A6 — A11 (on digital pins 4, 6, 8, 9, 10 and 12). The Micro ATmega32U4-MU has 12 analog inputs (A0 — A11), all of which can also be used as digital i/o. Analog inputs A0 — A5 appear in the same locations as on the Arduino Uno; inputs A6 — A11 are on digital i/o pins 4, 6, 8, 9, 10 and 12, respectively. Each analog input provide 10 bits of resolution (1024 different values). By default, the analog inputs measure from 0 to 5 volts, though it is possible to change the upper end of their range using the AREF pin and the analog Reference() function.
— Reset. A low signal level resets the microcontroller.
LEDs
* RX and TX — flash when data is being transmitted via USB connection.
* ON — power indicator.
* L — LED connection to digital pin 13.
Memory
The ATmega 32U4 microcontroller has 32 KB memory (with 4 KB used by the bootloader). It also has 2.5 KB SRAM and 1 KB EEPROM (which can be read and written with the EEPROM library).
The Micro ATmega32U4-MU has a number of facilities for communicating with a computer, another Arduino device or microcontrollers.
The ATmega32U4 provides serial UART TTL serial communication, which is available on digital pins 0(RX) and 1(TX).
Having hardware support for USB, the ATmega32U4 also allows for serial communication with the computer over a virtual COM port.
The Micro ATmega32U4-MU also acts as a USB 2.0 device, using standard USB COM drivers. The Arduino software includes a serial monitor that allows simple textual data to be sent to and from the board. Which we will do in the example given under the description.
A SoftwareSerial library allows for serial communication on any of the ATmega32U4-MU’s digital pins.
The ATmega32U4 also supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the 12C bus. The SPI library can be used for SPI communication.
Programming
The board can be programmed with Arduino software, by selecting ATmega32U4 in the Board menu.
The ATmega32U4 microcontroller on the Micro ATmega32U4-MU comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer.
You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header.
Automatic Reset
Rather than requiring a physical press of the reset button before an upload, the Micro ATmega32U4-MU is designed in a way that allows it to be reset by Arduino software running on a connected computer. The reset is triggered when the virtual CDC COM port is opened at 1200 baud and then closed. When this happens, the processor will reset, breaking the USB connection to the computer. After the processor resets, the bootloader starts, remaining active for about 8 seconds. The bootloader can also be initiated by pressing the Reset button. Note that when the board first powers up, it will jump straight to the user sketch, if present, rather than initiating the bootloader.
USB Overcurrent Protection
The Micro ATmega32U4-MU has a resettable polyfuse that protects the computer’s USB ports from shorts and overcurrent. Although most computers have their own internal protection, the fuse provides an extra layer of protection. If more than 500mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.
Microcontroller:ATmega32U4-MU
Power Out:3.3V-180m
5V-800m
Power IN. USB:5V
Power IN. VIN/DC Jack:5V
Power Consumption:5V 220mA
Logic Level:5V
USB:Micro USB
Clock Frequency:16MHz
Operating Supply Voltage:3.3V
Digital I/O:20(7-PWM)
Analog I/O:12
Data RAM Type/Size:2.5Kb
Data ROM Type/Size:1Kb
Interface Type:ISP
Operating temperature:−40㎡°/+85㎡°
PCB size (L*W):48.26*17.78mm
Weight:8.5g
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Package includes
1 x Micro ATmega32U4 5V 16MHz Development Board
Weight | 0.015 kg |
---|
Customers Also Viewed
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car Module
$41.54Driver ModuleAdd to cartDescriptionThe four channel L298N motor drive module integrates two L298N chips and can drive four DC motors to realize the control of forward and backward rotation and motor speed. The module is equipped with LM2596S step-down chip. If the motor with 7V voltage or more is driven, 5V power can be output to the control …
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car ModuleRead More
Geekcreit D1 Mini ESP32 ESP-32 WiFi+bluetooth internet of Things Development Board Based ESP8266 Module
$21.86Motherboard & Development BoardAdd to cartMore informations:https://github.com/LilyGO/ESP32-MINI-32-V2.0DescriptionThis is D1 Mini ESP32 ESP-32 WiFi+bluetooth Internet Of Things Development Board.Use exampleit can also match the next productPackage included4 x Long female pins4 x short female pins4 x Normal pins1 x mini D1 ESP32
AF1020 Dust-proof Probe Super-stable Pipe-type Current-type Temperature and Humidity Transmitter Temperature Senor Humidity Sensor
$176.16Solar CollectorsAdd to cartSpecificationModel:AF1020 Type Temperature and Humidity TransmitterTemperature measurement range:- 40 ~+80 (℃)Measurement accuracy:+-0.5 (℃)Working Voltage 15-36 (V)Humidity accuracy:+-3% RHHumidity measurement range:0-99.9% RHCurrent output:4-20 m AInstructions1. Power cord positive DC18~36V (red wire)2. Power ground wire GND (black wire)3. Humidity current output 4~20MA (yellow line)4. Temperature current output 4~20MA (white line)Installation sequence1. Connect the red, black, yellow and …
3Pcs 5M Meter thermometer Electronic Digital Display FY10 Embedded thermometer indoor and Outdoor Temperature Measurement
$20.72Test & Measuring ModuleAdd to cartFunction introductionOverall size:48*28*15mmInserted hole size:46*27mmLCD temperature display-50→ to 110→ temperature measurement, 0.1 degree resolution.C and F display versions are availableStandard 0.8m waterproof probeCable length:5 meterPackage includes3 x Thermometer
Peacefair PZEM-028 AC Digital Multifunction Meter Voltmeter Ammeter 0~100A/400V Power Factor Meter
$27.97Electronic Accessories & SuppliesAdd to cartError adjustmentThe product is 100% calibrated before leaving the factory, and the user can also manually adjust the error by himself. The method is as followsStep 1:Long press the button (about 3 seconds) until the digital digit on the screen flashes, then release the button;Step 2:Digital flashing means entering the error adjustment state, the digits …
3pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boards
$12.11Smart ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThe kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage Generator
$55.81Power Supply ModuleAdd to cartFeatureThe high-voltage module uses the principle Tesla coil is made of high-voltage pulse output voltage current, small size, high efficiency, simple external circuit(just plug in the switch, the battery can be) discharge intensity violent.SpecificationModel:MC-105Volume:Length 65mm Diameter 24mm, Diameter of cut surface 22mmVoltage:Input DC3.7-6V, output DC200-400KVCurrent:Input 4A, output 0.5ALength:Input 10 cm or so, the output is …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage GeneratorRead More
Reviews
There are no reviews yet.