5pcs Microphone Pickup Audio Microphone Amplifier Module DIY Kit Dual Track Output Gain Adjustable DC 12V 3.5mA MIC Sound Voice
$19.40
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Product name:Microphone with adjustable sensitivity
Working voltage:DC9-15V, 12V recommended
Working current:above 100mA
Response frequency:20Hz-20KHz
Monitoring range:about 100 square meters
Finished product size:length 56 * width 25 * height 16mm
Product net weight:15 grams
The power input has anti-reverse protection, which can effectively prevent the module from being damaged if the power is reversed.
Product description
This product uses a low-noise processing chip, plus a diaphragm capacitor microphone, combined into a power amplifier that can be connected to audio input.
Can directly monitor the subtle sound of the scene. Equipped with a trimming resistor, which can adjust the sensitivity and easily change the monitoring distance and range.
Scope of application
It can be used in factories, banks, schools, trains and other production facilities that need to be monitored. It can be used as auxiliary equipment such as monitoring and synchronous recording. It can also be used as a megaphone with the power amplifier. Connecting two modules can be used as an intercom system.
Tips
When the signal is too strong, or the pickup and the speaker are close together, self-excitation may occur. At this time, you can set the amplifier volume.
Turn down or reduce the sensitivity on the module.
The positive and negative sides of the interface are marked, pay attention to it when wiring.
The output needs to be connected to the amplifier to hear the sound, and cannot be directly connected to the speaker. Do not need to connect the amplifier when recording.
Package included
5 x Microphone Pickup Audio Microphone Amplifier Module DIY
Weight | 0.105 kg |
---|
Customers Also Viewed
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water Heater
$21.87Laboratory Heating EquipmentsAdd to cartDC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterSpecificationsModel:SSG-2Type:Normally ClosedMaterials:Plastic & CopperDimension:83*90*49cmPipe Inside Diameter:1/2 inchNet Weight:(approx.) 190gFeaturesThis is a DC12V solenoid valve usually used for solar water heater.It can work with water from 1 to 100℃ (or some other liquid).Working Voltage Range:Rated Voltage ±10%Working Water Pressure:0.02 to 0.8MpaThe working water pressure would be too low/high to …
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterRead More
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set Kit
$76.17Terminal BlocksAdd to cartDescription650 Pcs Assorted Ring Insulated Electrical Wire Terminals Crimp Connector Set KitSpecificationQuantity:650PcsMaterial:Copper + PVC+ TinplateInsulated crimp terminals.All are enclosed in plastic case for easy access.The assorted crimp terminals is including50 x Ring M3 Red50 x Ring M4 Red50 x Ring M5 Red50 x Ring M6 Red50 x Ring M8 Red50 x Ring M4 Blue50 x …
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set KitRead More
3.5 inch Protective Enclosure Case Support Dispaly Screen or Cooling Fan for Raspberry Pi
$9.26Raspberry Pi & Orange PiAdd to cartFeatures– Fully updated for Raspberry Pi 3B+/3B/2B– Can support 3.5 inch screen or cooling fan (notes:can not assemble them at the same time)– Heat sink openings for both CPU and LAN chip– High-gloss finish, surface mountableSpecificationsColor:BlackMaterial:ABSSuitable for Raspberry Pi 3B+/3B/2BWeight:45gSize:9cm*6.2cm*3.4cmPackage Included1x ABS Case4x Non-slip mat4x Screws
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module for
$47.25DIY Electronic KitsAdd to cartDescription1. Use TM1650 (compatible with AIP650) digital tube driver chip, support 8-level brightness adjustment, working voltage 3.3V ~ 5.5V2. IIC interface, only need 2 ordinary IO can drive, do not need to repeat scanning of MCU, saving MCU resources.3. 4 digit 0.56 inch red common negative digital tube with decimal point.4. 0.56 inch with four …
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module forRead More
WEAH-81 Car Heavy Bass Frequency Divider High and Low 2-way 2 Bass Crossover Upgrade Tool
$33.09Amplifier BoardAdd to cartFeatureBrand:WEAHModel:81Power:100WApplicable impedance:4-8ohmFrequency response:100Hz ~ 45HzDimensions:133 x 95 x 44mmApplication environment:Car or home speaker DIYPackage includes1 x Bass Frequency DividerHow to Wire:
5pcs 8-36W intelligent Sensor LED Ceiling Light And Sound Control Power Supply Module Bulb Panel Light Built-in Power Driver
$21.42Power Supply ModuleAdd to cartDescriptionInput Voltage:AC185-265VOutput Current:0.22AOutput Voltage:24-108VEfficiency:90%Working Frequency:50/60HZOutput Power:8-24WSound Control:50-75dBLight control:7-20LuxDiameter:25.8mmFeature1. The combination of sound and light control, when the light is strong, does not work, the light intensity is lower than 12-15LUX, and the sound of the induction 27-36DB starts automatically.2. Delay 40-60S automatically extinguished, easy to install, compatible with ordinary switches, no additional wiring.3. Single trigger, …
Reviews
There are no reviews yet.