DIY Music Tesla Coil Module Kit ZVS Technology Physics Electronics Small Tesla Spare Parts
$37.17
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Power supply input voltage:24V DC;
Power supply current:2A-3A;
Power supply interface:Both positive and negative in 5.5-2.1;
Circuit board size:5.4CMx5.4CM;
Coil size:The diameter of 5.05CM is about 7CM
DIY bulk weight:135 grams; Finished product:115 grams;
Coil number:The 250 circle, the enameled wire with a coil diameter of 0.2, is wrapped around the coil.
The volume of the volume will be larger than the volume of the headset;
Audio interface:The 3.5 socket can pick up the audio source of mobile phone, MP3 and computer.(the computer audio interface is 3.5, the audio line used 3.5 to 3.5 audio line, mobile phone and MP3 interface is different, please use the corresponding audio line to turn 3.5).If there are other voltage and current sources which are not up to the requirements, or devices will burn out, the loss will be borne by the buyer.
Some buyers think that the power supply is 24V, then the input 12V device will not be damaged. This understanding is wrong. The circuit will eventually constitute an oscillating circuit.
If the voltage and current are not enough, the circuit will not oscillate, which will cause the transistor to directly connect to the ground, and the transistor will burn down.
Package Included
1 x DIY Music Tesla Coil Module Kit
| Weight | 0.195 kg |
|---|
Related products
3Pcs DIY CD4060 SMD Music LED Light Kit Electronic Experimental Training Teaching
$20.61DIY Electronic KitsAdd to cartWorking principleUsing the SMD CD4060 control 12 red, yellow and green LED flashing, adjust RP1 can change the speed of flashing, while the music chip issued a wonderful music. The kit uses SMD components and plug-in components, is ideal for practical training requirements.The CD4060 consists of an oscillator and a 14-bit binary serial counter bit. …
3Pcs DIY CD4060 SMD Music LED Light Kit Electronic Experimental Training TeachingRead More
3Pcs DIY Touch Vibration Alarm Kit Electronic Training Teaching
$11.65DIY Electronic KitsAdd to cartWorking principleThe touching vibration alarm consists of touch trigger circuit, vibration trigger circuit and alarm circuit. The 555 time base circuit U1 forms the typical monostable operating mode. The transient time is determined by the values of RP1, R2 and C2.Usually the circuit is in steady state, 555 time base circuit 3 pin output low, …
3Pcs DIY Touch Vibration Alarm Kit Electronic Training TeachingRead More
10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49DIY Electronic KitsAdd to cartUseSchool science experiment, electronic equipment, negative ion generator, small scientific production and so on. FeatureThis circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.NoteThis transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage …
10Pcs inverter Boost High Voltage Generator 15KV High Frequency TransformerRead More
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.