5pcs TES1-4903 20x20x3.6mm 5V 3A thermoelectric Cooler Semiconductor Refrigeration Film Heatsink Peltier Plate Module
Shipping:Standard Shipping about 10-25 business days
Note for use in refrigeration
1. The red wire is connected to the power wire is connected to the anode, cathode, and without cooling conditions, the instantaneous power of the test, which touch the two end of the refrigerator, you will feel a fever, a little have a fever cold, heat, cold side cold. But time can not exceed 5 seconds, otherwise the hot end temperature is too high, extremely easy to cause the device to burn out.
2. Under normal conditions, the lead with red is usually expressed as the positive pole:usually with black as the negative, this is the work of the thermoelectric cooler wiring method. When the current polarity is changed, the polarity of the current can be changed. Refrigeration work must adopt the switching power supply, power supply ripple coefficient should be less than 10%.
3. The number of the thermocouple and the limit voltage of the thermocouple identification method, the number of pairs of thermocouple P, N node. For example:cooler model for TEC1-12706, 127 for cooler thermocouple logarithm, 06 allowable current value:A, the threshold voltage is logarithmic thermocouple cooler * 0.12, for example:limit voltage V TECI-12706 = 127 x 0.12 = 15.4 (V). The normal operating voltage is 78% of the limit voltage, such as the working voltage of 15.4*0.78=12.01V is TEC1-12706.
4. All kinds of cooler in use or in the test, the cooling and heating temperature of hot and cold exchange should be returned to the room temperature (usually more than 15 minutes). It is easy to cause damage of refrigerator.
5. In order to prolong the life of the thermoelectric cooler, sealing the deal with refrigeration components around. We have two kinds of methods, one is the use of 704 silicone seal; the other is a mining epoxy resin seal, seal is designed to make the refrigerator completely isolated thermocouple with the outside air. Plays the role of anti moisture and moisture, and can prolong the life of the cooler.
6. At the time of installation, the first two will wipe the refrigeration assembly clean, and in cooler for hot and cold surface evenly coated with a thin layer of thermal grease. The surface contact with the cooler is aluminum radiator or cold storage plate should be smooth, and wipe clean, also on the surface evenly coated with thermal grease; cooler during installation must be good contact with the cold storage cold plate, hot surface should also fully contact surface and the aluminum radiator, (as with screw fastening screws, several force should be uniform, not excessive or uneven force). In order to achieve the best cooling effect, application of thermal insulation material is filled between the cold storage board and aluminum radiator, the thickness of 25-30mm is appropriate.
7. Cooling plate suggested between 150PSI to 300PSI, the pressure is too low will cause cooling plate contact surface is bad, too much pressure, will damage the cooling plate.
8. The user has no special equipment in the case, to determine the cause of the cooler is qualified, mainly to test its resistance. You can use a data bridge or a resistance meter with compensation to measure the resistance of the cooler. Using a multimeter to test the static resistance refrigeration component is not accurate, only for reference.
9. In the process of handling and installation of the refrigerator, the operator should be gently, no refrigeration piece fall from a height, even at the height of the 10-20cm will cause the internal resistance of cooler produced significant changes, resulting in damage to the refrigerator.
10. A semiconductor refrigerating sheet used in the following situations, the life may be cut:A, the frequent use of alternating hot and cold B, vibration condition using C, a hot end radiator temperature exceeds 65 degrees D, working voltage (recommended the use of overpressure does not exceed the limit voltage 70%) cooling plate heating surface E, cooling plate contact F, not around the sealing glue used in humid environment
11. A semiconductor refrigerating sheet used in the following occasions, there will be rapid damage may:heating surface A, cooling pad does not contact any cooling objects B, cooling plate voltage exceeds the limit voltage pressure C, cooling plate more than 500PSI.
5 x TES1-4903 thermoelectric cooler
Customers Also Viewed
50W Solar Panel Kit MPPT Solar Charge Cotroller 12V Battery Charger 10-100A LCD Controller for Phone Caravan Van Boat$58.71
3Pcs TDA2030A Subwoofer Amplifier Board 2.1 3-Channel Compatible LM1875$52.68Amplifier BoardAdd to cart
The main parametersLeft and right channels:TDA2030Ax2. Power:18W + 18W, suggested 2.5-4 inches, 4-8 ohms 10-30W of full-range speakers.Bass output:TDA2030Ax1, Power:18W (≤250HZ) suggested 5-8 inches, 4-8 ohms 20-50W woofers.Power:AC double AC9-15V transformer, we recommend double AC12V power is above 25W (2A) transformer.PCB Materials:FR-4 fiberglass board, thickness:1.6mm.Board Size:79 x 95 x 60mm (length x width x height), …
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module$32.04Electronic Accessories & SuppliesAdd to cart
40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
5Pcs UNO R3 ATmega16U2 AVR Development Module Board$72.09Motherboard & Development BoardAdd to cart
Note:This version does not includes USB cableUNO R3 DescriptionThis UNO R3 board is 100% compatible with original one, now it has perfect quality and performance .This is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. It can be used to develop stand-alone interactive …
ESP32-CAM WiFi + bluetooth Development Board ESP32 with FT232RL FTDI USB to TTL Serial Converter 40 Pin Jumper$34.98Motherboard & Development BoardAdd to cart
[ESP32-CAM Wireless Module]Description1. ESP32-CAM is a WIFI+ bluetooth dual-mode development board that uses PCB on-board antennas and cores based on ESP32 chips. It can work independently as a minimum system.2. ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip …
BESTEP 6 Channel 12V Relay Module Low Level Trigger with Optocoupler Isolation$14.34Relay ModuleAdd to cart
DescriptionMaximum load:AC 250V/10A, DC 30V/10A.The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.Working voltage is 12V.Each channel of the module can be set up by high jumper or low level trigger.Fault tolerant design, even if the control line is broken, the relay will not act.Power indicator (green), 6 relay status indicator (red).The …
3pcs DIY Electronic Kit Electronic Candle Making Kit Ignite Blow Control Simulation Candle Electronic Training DIY Parts$10.04DIY Electronic KitsAdd to cart
DescriptionKit Name:Analog Electronic CandleBoard size:42mm*33mmCircuit board material:glass fiberWorking voltage:DC 5VBoard function:simulate ignition, blow candles, fun, and realize the function of electronic candle.The kit needs to be soldered and installed by the buyer.Package included3 x Simulation Candle Electronic Training DIY Parts