3pcs 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal
Shipping:Standard Shipping about 10-25 business days
Normally open interface maximum load:AC 250V/10A, DC 30V/10A.
SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA.
Fault-tolerant design, the relay will not move even if the control line is broken.
Power indicator (green), relay status indicator (red).
The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient.
Two module interface
1. DC+:Connect the power supply positive pole (voltage 3.3V).
2. DC-:Connect the power negative pole.
3. IN:Low level (3.3V) control relay pull in.
Relay output terminal
1. NO:Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.
2. COM:Relay common interface
3. NC:Relay normal close, short connected with COM before pulling inand suspended after pulling in.
3 x 1 Channel 3.3V Relay Module
Customers Also Viewed
5pcs USB Digispark Kickstarter ATTINY85 for Micro USB Development Board OPEN-SMART for Arduino – products that work with official for Arduino boards$28.66Motherboard & Development BoardAdd to cart
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionAbout the USB Digispark is an Attiny85 based microcontroller development board similar to the for Arduino line, only cheaper, smaller, and a bit less powerful.With a whole host of shields to extend …
5pcs 12V Volume infrared induction Switch Module LED Lamp Sensor Switch Module$46.85Sensor & Detector ModuleAdd to cart
DescriptionAutomatic control products based on infrared technology, when someone enters the switch induction range, the sensor detects the change of infrared spectrum of human body. The switch automatically turns on the load, and the switch keeps moving without leaving the induction range. After the person leaves, the switch automatically closes the load with a delay. …
GDCPH 2.7V60F Super Farad Capacitor Module 13.5V12F Backup Power Rectifier$23.76Electronic Accessories & SuppliesAdd to cart
FeaturesFast charge and discharge.Long life. Large capacity. High power density. Good low temperature characteristics.SpecificationBrand:GDCPHModel:13.5V12FSeries:Super capacitor (13.5V)Nominal capacity:12FTolerance:10 (%)Rated voltage:12-13.5V (V)Working temperature range:-20~65→Termination type:weldingLead spacing:101mmSize:101mm*42mm*20mm(Length * height * width)Height-installation (maximum):42mmShell:aluminum shellPackage included1 x Super capacitor
5pcs ACS712 Module 30A Current Detection Board ACS712 Hall Current Sensor Module$20.52Sensor & Detector ModuleAdd to cart
>>>Manual:Click here to openFeaturesThe current sensor chips:ACS712ELC-30APin 5V power supply, on-board power indicator;No test current through the output voltage is VCC / 2;PCB board size:31 (mm) x13 (mm);NoteACS712 is based on the principle of the Hall test, please use this field to avoid impactPackage Included5 x 30A Current Sensor Module ACS712T
10 pcs DC 5V 5mW 650nm 6mm Laser Dot Diode Module Red Copper Head Tube$8.73Module ComponentsAdd to cart
FeaturesWorking life:more than 2000 hoursSpot mode:dot facula, continuous outputLaser wavelength:650nm (red)Copper head diameter:6mmLight powerSupply voltage:5V DCOperating currentOperating temperature:-36→ ~ 65→Power lead length:120mmShell material:brassSingle weight:1gPackage included10 x Laser diode dot
M5Stack PRO 13.2 Universal DIY Pro Stack Module 2.54 mm Hole Pitch ProShield for ESP32 Protype Expansion Board$13.11Expansion Board & ShieldAdd to cart
DescriptionPRO 13.2 is a universal DIY pro module in the m5stack stack module series, with a height of 13.2mm. You can easily build your own custom circuits by using this module. You can design and build the protype circuit according to your own needs, and interact with the M5 Core on the top layer through …