SI24R1 NF-01-S 2.4G Wireless Serial Module Transparent Transmission
$6.55
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
NF-01-S is a 100mW power 2.4G wireless module, high-altitude rate (up to 2Mbps), using SPI interface, send and receive in one pure hardware module; high stability, cost performance, Volume, use of all-industry components.
Has been mass production and reached millions of shipments, and applies to a variety of application scenarios.
NF-01-S can be widely used in a variety of networking occasions, suitable for wireless mouse and keyboard, wireless remote control, somatosensory equipment, active RFID, NFC, low power consumption network of wireless sensor networks, is the ideal solution of Internet of Things application.
NF-01-S adopt DIP-8 package, whether learning or mass production, can quickly docked to existing products, no need soldering, direct plug, easy to use.
Information link:http://wiki.ai-thinker.com/2.4g
Features
• DIP-8 ultra-small package, built-in 2.4G antenna, small size, easy to use
• Supports data reception for six channels
• Supports common modulation such as GFSK / FSK
• Supports 2Mbps / 1Mbps / 250Kbps data rate
•Multi-frequency:126 frequency, to meet the needs of multi-point communication and frequency hopping communication
• Internal integration of high PSRR LDOs
• Wide supply voltage range:1.9 ~ 3.6V
• Average emission current as low as 110mA
• Receiver sensitivity:-96dBm @ 250kbps
• Maximum transmit power:+ 7dBm
• Four-wire SPI interface for up to 10MHz
• Internal Integrated Smart ARQ Baseband Protocol Engine
• Transmit data hardware interrupt output
• Supports 1bit RSSI output
• Low application cost:The SI24R1 integrates all the high-speed signal processing parts associated with the RF protocol, such as automatic retransmission of lost packets and automatic generation of response signals. The SPI interface of the SI24R1 can be connected using the microcontroller’s SPI port or using the microcontroller I / O port to simulate, the internal FIFO can be with a variety of high and low speed microprocessor interface, easy to use low-cost single-chip.
• Easy to develop:Since the link layer is fully integrated on the module, it is very easy to develop. Automatic retransmission function, automatic detection and retransmission of lost packets, retransmission time and the number of retransmission software can automatically control the automatic response is not received a reply signal packet automatic response function, after receiving the valid data, the module automatically sends a response Signal, no additional programming Carrier detection – Fixed frequency detection Built-in hardware CRC error detection and point-to-multipoint communication Address control Packet transmission error Counter and carrier detection function can be used for frequency hopping settings can be set at six simultaneous receive channel address, can be selective Of the open receiving channel standard pin DIP 2.54mm pitch interface for easy embedded applications.
Parameter
Model:NF-01-S
Package:DIP-8
Size:28.6*15.3*3.2 mm
Communication Interface:SPI (The maximum rate of up to 10Mbps)
Air rate:250k~2Mbps, 3 Level adjustable(250kbps,1Mbps,2Mbps)
Spectral range:2400MHz~2525MHz adjustable, 1MHz Step forward
Antenna form:Onboard PCB antenna, gain 2dBi
Maximum transmit power:7dBm
Receiving sensitivity:-96dBm@250kbps
Average current:Emission current:25mA(7dBm)
Receive current:15mA (2Mbps)
Shutdown:current 1.0uA(Shutdown Mode)
Power supply range:1.9~3.6V, Typical value 3.3V
Operating temperature:-20 → ~ 85 →
Storage environment:-20 → ~ 90 → ,
Pin Explanation
NO.:Name:Direction:Use
1:VCC:-:Power supply, must be between 2.0 ~ 3.6V
2:GND:-:Ground, connected to the power supply reference ground
3:CSN:Input:The module chip select pin, is used to start an SPI communication
4:CE:Input:Module control pin
5:MOSI:Input:Module SPI data input pin
6:SCK:Input:Module SPI bus clock
7:IRQ:Output:Module interrupt signal output, low level active
8:MISO:Output:Module SPI data output pin
Package included
1 x SI24R1 NF-01-S 2.4G Wireless Serial Module
Weight | 0.001 kg |
---|
Customers Also Viewed
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5V
$26.35Power Supply ModuleAdd to cartDescriptions3-Cell(3S) VersionInput voltage:DC 4.5V-5.5V(Recommend DC 5V)Charging voltage about:4.05V-5.1VCharging current about:230mA-240mAUSB power protectionShort circuit protection and zero volt battery activationBattery protectionOperating ambient temperature:-40° to +85°Storage temperature:-65° to +125°Size:30x 15 x 4mmNoteThe output voltage cannot be measured with a multimeter without a battery. But can be observed with an oscilloscope.Applicationskids toys carDigital CamerasSolar chargingBluetooth ApplicationsAudio equipmentDigital CameraElectronic …
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5VRead More
5Pcs/Pack 5V 1000mA 165*165mm Monocrystalline Solar Panel Cells with Positive&Negative Cables
$85.54Smart Robot & Solar PanelAdd to cartFeaturesProvide you with high conversion rate and incredibly efficient output.Excellent performance even under the weak sunlight.Portable and solid casing.Application:to charge, for home lighting and different kinds of low-power appliances, for science projects, for solar powered water pump, small solar power system, etc.SpecificationsType:Monocrystalline Size:165*165mmCurrent:1000mA Net Weight:about 600g one packPackage Content:5Pcs x Poly Solar PanelVoltage:5VMPN:Does Not ApplyPackage …
Waveshare 1.54 inch ink Screen Module 152×152 Electronic Paper SPI interface Yellow Black and White 3-color Display
$45.91Display ScreenAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openDatasheet:Click here to openGithub:Click here to openFeaturesNo backlight is needed, and the display content of the last screen can be kept for a long time after power offVery low power consumption, basically only consumes power when refreshingSPI control interface, can be connected to Raspberry/Nucleo and other main control …
Geekcreit DIY Creative Electronic Watch Kit 51 Single-chip LED Digital Tube Clock Training Production Kit
$15.30DIY Electronic KitsAdd to cartDescriptionName:LED Electronic Watch KitPower supply:CR2025 3V button battery (available for testing, there are inevitably extra factors causing insufficient power.)Display:LED red digital tube displaySize:52*52*18mmInstallation:the board need to solder yourself and then assembly the caseFunction:You can press the digital tube button when need to wacth time; it will enter the power saving mode automatically after 5 seconds. …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal Board
$3.56Expansion Board & ShieldAdd to cartQFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardSpecificationDimension:20.25 x 40.64mm / 0.79inch x 1.60inchThickness:1.5mmPanel:FR4DescriptionThe PCB board has two sides.A side for pin pitch size 0.80mm, B side for pin pitch size 0.80mm.It can be used to convert QFN32/QFP32 (600mil width, 2.54mm pin pitch).You can solder filter capacitors or resistors to increase stability and …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardRead More
YJ0007 180W Car Stereo Audio Amplifier Power Boost Board Single 12V input Conversion Double 32V Output
$52.41Boost & Buck ModuleAdd to cartDescriptionAll parts and components of this product are original products, unpretentious and pure in quality; using high-quality original parts not only guarantees safety and quality, but also has a long service life, and more importantly, it is a strong guarantee that the actual performance can reach the design goals.Features1. All components are genuine.2. The main …
Reviews
There are no reviews yet.