Geekcreit 400W DC-DC High Power Constant Voltage Current Boost Power Supply Module
Shipping:Standard Shipping about 10-25 business days
Module Properties:Non-Isolated Boost Module (BOOST)
Input current:15A (MAX) exceeds 8A
Static operating current:10mA (12V 20V, the higher the output voltage, the static current will increase)
Output voltage:10-60V continuously adjustable (default output 19V shipment, if you need other voltage please explain to the dispensers.)
12-80V fixed output (for volume customers)
Output current:When 12A MAX exceeds 7A, please strengthen the heat dissipation (related to input and output pressure difference, the larger the pressure difference is, the smaller the output current is)
Constant current range:0.2-12A
Output Power:= input voltage * 10A, such as:input 12V * 5A = 60W, input 24V * 5A = 120W,
Input 36V*5A=180W, input 48V*5A=240W,
Working temperature:-40~+85 degrees (enhance heat dissipation if the ambient temperature is too high)
Conversion efficiency:up to 96% (efficiency is related to input, output voltage, current, differential pressure)
Overcurrent protection:Yes (If the input exceeds 15A, the output voltage is automatically reduced and there is a certain range of error.)
Input reverse protection:No, (If you need more reverse current, please input the string into the diode)
Installation method:4pcs 2.5mm screw holes
Connection mode:Wiring output
Output voltage/current regulation method
1. Adjust the “CV-ADJ Inch potentiometer and set the output voltage to your desired voltage according to your battery or LED. Such as 10 series LED voltage regulation 37V. (Increase the reverse clock voltage, reduce the clock voltage)
2. Turn the inchCC-ADJinch potentiometer counterclockwise for about 30 turns, set the output current to the minimum, connect the LED, and adjust the RV2 potentiometer to your desired current. For battery charging, after discharging the battery, connect it to the output and adjust the RV2 to the current you need. (For charging, be sure to use the discharged battery to adjust, because the battery is more More, the smaller the charging current is.) (Reverse clock current is reduced and clock current is increased)
Please do not adjust the current by short circuit. The circuit structure of the boost module cannot be adjusted by short circuit.
1, DIY a power supply, input 12V can be, the output can be adjusted 12-50V.
2, for your electronic equipment power supply, you can set the output value according to your system voltage.
3, as the car power supply, power your laptop, PDA or a variety of digital products.
4, a high-power notebook mobile power DIY:coupled with a large-capacity 12V lithium battery pack, so that where your notebook can be lighted where.
5, solar panel voltage regulator.
6, to the battery, lithium battery and other charges.
7, drive high-power LED lights.
1 x 400W DC-DC High Power Constant Voltage Current Boost Power Supply Module
Customers Also Viewed
433MHZ Low Pass Filter LPF Module$26.03RF amplifierAdd to cart
DescriptionThe low-pass filter allows signals below the cutoff frequency to pass, while signals above the cutoff frequency are attenuated. It is often used to suppress the high-order harmonics of electromagnetic signals, or to filter out high-frequency clutter at the back of the mixer to play the role of frequency selection. This filter can greatly attenuate …
RF Signal Source AD9959 Signal Generator 4 Channel DDS Module Performance Is Far More Than AD9854$119.46RF amplifierAdd to cart
FeatureName:UAF42 filterSize:81x61mmSupply voltage:DC5VInfos:Click here!Chip Features1. Four 500 MSPS synchronous DDS channels2. Independent frequency / phase / amplitude control between all channels3. Frequency, phase and amplitude changes when the delay match4 excellent channel isolation5. Sweep function6. Up to 16 modulation (pin selection)7. Programmable DAC full-scale currentChip ApplicationsStochastic local oscillator (LO) frequency synthesisPhased array radar / sonarInstrumentationSynchronous …
16-Channel 9-36V USB Electrical Module Serial Port Relay Motherboard$59.04Relay ModuleAdd to cart
>>>More information:Click here to openFeatureThis is USB controlled relay opto-isolated board with 16 SPDT relays.You can use it for simple ON/OFF switching electrical devices – home lights, DC motors, solenoids and others.It can help you building projects like robotics and home automation.Maximum load:10A/250VPower supply:DC 9V~36VLED for each relay outputPower LEDUSB LEDPackage includes1 x Relay board
CJMCU-9306 PCA9306 2-Bit Bidirectional I2C Bus And SMBus Voltage Level Translator$8.73Converter BoardAdd to cart
DescriptionCJMCU-9306 device is a dual bidirectional I2C and SMBus voltage-level translator with an enable (EN) inputand is operational from 1.2-V to 3.3-V VREF1 and 1.8-V to 5.5-V VREF2.The PCA9306 device allows bidirectional voltage translations between 1.2 V and 5 V, without the use of a direction pin.The low ON-state resistance (RON) of the switch allows …
Carb Carburetor Sets for Honda F Predator 420CC 188F Generator Engine 5000W 8750W 7000W 6500W$46.56Solar CollectorsAdd to cart
Specifications-Material:Metal-Type:Carburetor-Fits for Honda Predator 420CC 5000W 8750W 7000W 6500W 188FFeatures-Durable,stable,high sensitivity.-Fitting for Honda Predator 420CC.-A perfect aftermarket replacement.-Easy to install.( instruction is not included)Package Included-1 x Carburetor for Honda -3 x Gaskets-1 x Fuel Line -2 x Fuel Filters -1 x Joint Filter
10Pcs Micro USB TP4056 Charge And Discharge Protection Module Over Current Over Voltage Protection$17.21Battery Protection ModuleAdd to cart
CharacteristicOn-board TP4056 lithium battery charging management chipOn-board micro USB head, can be directly connected with most of the smart phone charger as the input side to the lithium battery chargingReserved IN+ and IN- input port, convenient user DIYOn-board charging status indicatorSupport charge discharge over current protectionChip with constant current and constant pressure, full automatic stopSupports …