Geekcreit 400W DC-DC High Power Constant Voltage Current Boost Power Supply Module
$19.67
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Module Properties:Non-Isolated Boost Module (BOOST)
Input voltage:DC8.5V-50V
Input current:15A (MAX) exceeds 8A
Static operating current:10mA (12V 20V, the higher the output voltage, the static current will increase)
Output voltage:10-60V continuously adjustable (default output 19V shipment, if you need other voltage please explain to the dispensers.)
12-80V fixed output (for volume customers)
Output current:When 12A MAX exceeds 7A, please strengthen the heat dissipation (related to input and output pressure difference, the larger the pressure difference is, the smaller the output current is)
Constant current range:0.2-12A
Output Power:= input voltage * 10A, such as:input 12V * 5A = 60W, input 24V * 5A = 120W,
Input 36V*5A=180W, input 48V*5A=240W,
Working temperature:-40~+85 degrees (enhance heat dissipation if the ambient temperature is too high)
Working Frequency:150KHz
Conversion efficiency:up to 96% (efficiency is related to input, output voltage, current, differential pressure)
Overcurrent protection:Yes (If the input exceeds 15A, the output voltage is automatically reduced and there is a certain range of error.)
Input reverse protection:No, (If you need more reverse current, please input the string into the diode)
Installation method:4pcs 2.5mm screw holes
Connection mode:Wiring output
Module Size:67mmx48mmx28mm
Output voltage/current regulation method
1. Adjust the “CV-ADJ Inch potentiometer and set the output voltage to your desired voltage according to your battery or LED. Such as 10 series LED voltage regulation 37V. (Increase the reverse clock voltage, reduce the clock voltage)
2. Turn the inchCC-ADJinch potentiometer counterclockwise for about 30 turns, set the output current to the minimum, connect the LED, and adjust the RV2 potentiometer to your desired current. For battery charging, after discharging the battery, connect it to the output and adjust the RV2 to the current you need. (For charging, be sure to use the discharged battery to adjust, because the battery is more More, the smaller the charging current is.) (Reverse clock current is reduced and clock current is increased)
Please do not adjust the current by short circuit. The circuit structure of the boost module cannot be adjusted by short circuit.
Application range
1, DIY a power supply, input 12V can be, the output can be adjusted 12-50V.
2, for your electronic equipment power supply, you can set the output value according to your system voltage.
3, as the car power supply, power your laptop, PDA or a variety of digital products.
4, a high-power notebook mobile power DIY:coupled with a large-capacity 12V lithium battery pack, so that where your notebook can be lighted where.
5, solar panel voltage regulator.
6, to the battery, lithium battery and other charges.
7, drive high-power LED lights.
Package included
1 x 400W DC-DC High Power Constant Voltage Current Boost Power Supply Module
Weight | 0.08 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.