3pcs JDY-10 bluetooth 4.0 Module BLE bluetooth Serial Port Module Compatible with CC2541 Slave
$16.47
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Model:JDY-10 bluetooth 4.0 slave module
Kernel:M0
Communication interface:serial port
Working voltage:1.9-3.6V
Communication distance:100 meters
Working current:90ua
Suspen mode:14 uA
Module is:bluetooth 4.0 slave
JDY-10 transparent transmission module is based on bluetooth 4.0 protocol standard, working frequency range is 2.4GHZ range, modulation mode is GFSK, maximum transmission power is 8db, maximum transmission distance is 80 meters, low power consumption, small size, strong signal, data transmission Stable and other characteristics.
Features
1:Support Android, IOS mobile phone data penetration
2:Support low power consumption (standby current can reach several uA)
3:Support GPIO and UART peripheral interface
4:Support AT command operation
5:Can be certified by FCC/CE and other standards
Product application range
1:bluetooth LED lighting
2:Motor adjustment and other products
3:Anti-lost alarm and other products
4:Sports Health Care
5:Small appliances
6:Automotive Electronics
Technical specifications
Type:Specifications
Working voltage:1.9 – 3.6V
Operating temperature:-40 – 85°C
Maximum transmit power:+8dbm
Antenna:PCB onboard antenna
Receiving sensitivity:-92dbm
Average current:Wake mode:90uA
Suspen mode:14 uA
Deep Sleep mode:1uA
Factory default configuration
Service UUID:FFE0
Feature UUID:FFE1
Serial port baud rate:115200bps
AT instruction set
Users can communicate with the bluetooth chip through the serial port. The serial port uses Tx, Rx two signal lines, and the baud rate is supported.
Hold 2400, 4800, 9600, 14400, 19200, 38400, 57600, 115200. The default baud rate of the serial port is 115200bps.
Instruction set details
(Note:You must enter and enter the line when you send the AT command. The AT command can only take effect when the module is not connected. Once the blue is enabled.
When the tooth module is connected to the device, the bluetooth module enters the data transparent transmission mode)
Detailed instructions
(AT commands are case sensitive and end with carriage return, newline characters:rn)
1. Get the version number
command:response:parameter
AT+VER:+:Param:version
Default:+JDY-10-V1.8
2. Get the bluetooth MA C address
command:response:parameter
AT+MA C:+MA C::Param:MA C address
3. Set the bluetooth name
command:response:parameter
AT+NAME:OK:Param:bluetooth name
Default name:JDY-10
Up to 18 bytes
4. Set / query – transmit power
command:response:parameter
AT+POWE
AT+POWE:OK
+POWE:Param:(0-5)
0:8db
1:5db
2:0db
3:-5db
4:-10db
5:-13db
5. Set / query – serial port baud rate
command:response:parameter
AT+BAUD:OK:Param:(0-7)
0:115200 bps
1:57600 bps
2:38400 bps
3:19200 bps
4:14400 bps
5:9600 bps
6:4800 bps
7:2400 bps
AT+BAUD:+BAUD
6. Set / query – broadcast interval
command:response:Parameter
AT+ADVINT:OK:Param:(0-6)
0:100ms
1:100ms
2:250ms
3:500ms
4:1600ms
5:3200ms
6:4800ms
AT+ADVINT:+ADVINT
Package included
3 x JDY-10 bluetooth 4.0 Module
Weight | 0.036 kg |
---|
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.