DIY Airband Radio Receiver Aviation Band Receiver Kit
Shipping:Standard Shipping about 10-25 business days
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Customers Also Viewed
2*100W TDA7498 Bluetooth 5.0 Digital Audio Amplifier Board Dual Channel Class D Stereo Decoded Remote Control Home theater Amp$32.79
YF-20 Stepper Motor Speed Controller Governor with LED Display Stepper Motor Speed Driver Control Module DC 7-30V$80.38Motor PWM Speed ControllerAdd to cart
Features– Can be directly connected to the stepping motor, no external driver.– High precision, adjustable speed, Angle can be set, and the speed can be real-time displayed.– Speed controller is made with high quality circuit board which ensures a longer service life.– This simple and easy-to-use DC motor speed controller has an stable performance.– Designed …
M5Stack Joystick HAT STM32F030F4 Supports Full Angular Movement and Center Press Push Button Switch Module fo$25.46Sensor & Detector ModuleAdd to cart
DescriptionJoystick HAT is one of the HAT module that is specifically designed for M5StickC. We have used a STM32F030F4 microprocessor inside to implement I2C communication with M5StickC.This mini-volume joystick module supports full angular movement and center press, and outputs angular data as well as button digital signals.With the ‘HAT’ unified plug-in design it can provide …
AFR-2000 1/4 Air Compressor Filter Water Separator Trap Tools Kit Regulator Gauge$40.49Electrical Pump & ValveAdd to cart
DescriptionAFR-2000 1/4inch Air Compressor Filter Water Separator Trap Tools Kit With Regulator GaugeFeaturesAir filter regulator is that adjust The main channel of air pressure to a pressure value what the control device required after filtration through decompression.No matter the size of the inlet pressure and flow fluctuations, always maintain a stable outlet pressure.Light weight, small …
10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter$19.04Other Module BoardAdd to cart
Features The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. users can directly use the IDE comes with an SD card to complete the library card initialization and read-write Module features are …
10pcs MD7105-SY 2.4G Wireless Module A7105 Transceiver NRF24L01 Board$44.82Smart ModuleAdd to cart
CharacteristicThe XL7105-D01 is a high-performance 2.4G wireless transceiver module based on Taiwan AMIC’s A7105 2.4G wireless transceiver IC. It uses GFSK modulation and works in the international ISM band of 2400-2483M. The high modulation rate of Zui is up to 500KBPS. Based on the SPI interface, the hardware SPI port of the MCU can be …
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79$15.30Other Module BoardAdd to cart
>>>Manual:Click here to openSpecificationsModel No.:HBVCAM-3M1917Model Size:30mm ≠ 25mm ≠ 5.0mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinityResolution:800LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:600WOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:OV3660 (1/5” )Seneor Package:CSP,Bare DieMaximum resolution:2048*1536Sensitivity:670mV /(lux-sec)Pixel Size:1.4┢m x 1.4┢m Maximum Image Transfer …
5Pcs GPIO Pin Reference Board for Raspberry Pi 2 Model B & Raspberry Pi B+$17.24Raspberry Pi & Orange PiAdd to cart
5Pcs GPIO Pin Reference Board For Raspberry Pi 2 Model B & Raspberry Pi B+FeatureCompatible with Raspberry Pi 2 Model B & Raspberry Pi B+Material:PCBWith marked you can easily distinguish all leads of GPIODimensions:5.3 cm x 1 cm x 0.1 cmPackage included5 x GPIO Pin Reference Board