DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
DC 2-12V to 12V 9V 9W USB Boost Power Supply Module Step Up Module DC Converter
$4.36Boost & Buck ModuleAdd to cartSpecificationsStarting voltage:2VInput voltage:2V-12V DCOutput voltage:12V DC (9V DC)Input current:2AOutput voltage:default 12V, 9V can be setOutput power:≤8w (in the case of input 5V, it is easy to overheat)No-load currentWorking temperature:-40 to -80 ° CBoard size:25*14*5mm (length * width * height does not include USB)The General Test Data (just for reference)Input DC2V boost to 12V output current …
DC 2-12V to 12V 9V 9W USB Boost Power Supply Module Step Up Module DC ConverterRead More
5Pcs DC24V Coil Power Relay LY2NJ JQX-13F DPDT 8 Pin PTF08A with Socket Base
$26.55Electronic Accessories & SuppliesAdd to cartSpecificationsModel:LY2NJ (8 pins)Coil voltage:DC24VCoil Power:DC (W):≤0.9AC (VA):≤1.2Contact Structure:8 pins 2 normally open 2 normally closedContact capacity:10A 250VACPull-in voltage:≤80% (V)Release voltage:DC:≥10% (V), AC:≥30%Contact resistance:≤50 (mΩ)Insulation resistance:≤100 (mΩ)Dimensions:27.5 * 21 * 35.3mmTerminals form:SocketAction time:20ms or lessReset Time:20ms or lessOperating frequencyMechanical 18,000 cycles / hourElectrical 18,000 times / hourPackage included5 x DC24V Coil Power Relay with socket base
40*160 0.5mm Blue Aluminum Alloy Water Cooling Block Radiator Liquid Cooler Heat Sink Equipment
$24.29Other Module BoardAdd to cartFeatures1. New high quality, Connector outer diameter 9.5mm, connector inner diameter 6-8mm.2. Inner flow channel extrusion.3. Welding from components to a whole one.4. Suitable for computer CPU water, industrial inverter drive, cooling, industrial switchboard cooling.5. Rate of less than 5X10-6 mbar.l/s parts.6. Internal fin thickness 0.5MM.SpecificationMaterial:luminum alloyColor:blueSize:pprox. 40x160x12mmProcessing:Vacuum auminum BrazingPackage includes1 x Water Cooling
20Pcs DS18B20 Temperature Sensor 18B20 TO-92 Encapsulation
$44.75Electronic Accessories & SuppliesAdd to cart20Pcs DS18B20 Temperature Sensor 18B20 TO-92 EncapsulationSpecificationTemperature measurement range:-55°C ~ +125°CAccuracy:± 0.5°CEncapsulation:TO-92Quantity:20pcsPackage included20 x DS18B20
20pcs WXD3-13-2W Precision Potentiometer 22K 22K Ohm Wirewound Multi-Turn Potentiometer
$49.11Module ComponentsAdd to cartSpecificationsResistance range:22K┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included20 x Potentiometer
Reviews
There are no reviews yet.