DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820io
$15.30Converter BoardAdd to cart>>>Manual:Click here to openOverviewUSR-ES1 embeds Wiznet’s W5500 chip, which uses hardware logic gates to implement the transport layer and network layer of the TCP/IP protocol stack (such as TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE, etc.), and integrates The data link layer, physical layer, and 32K bytes of on-chip RAM serve as data transceiving buffers. …
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820ioRead More
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module
$32.04Electronic Accessories & SuppliesAdd to cart40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
EQKIT KM-1 DC 6-12V PWM Motor Speed Controller Kit DIY Motor Speed Regulator Set Stepless Speed Control
$8.73Module KitsAdd to cartSpecificationsModel:KM-1Operating voltage:DC 6-12VPCB board size:40 x 40mmCircuit descriptionKM-1 uses PWM (pulse width modulation) to control the speed of the motor, adjust the pulse width duty ratio, so that the speed from zero to the maximum speed stepless speed regulation. The wider the crest width of the control waveform, the faster the motor speed; on the …
20pcs 63V 10000UF 105 High Frequency Temp Electrolytic Capacitor 30mm x 50mm Long Life
$108.62Electronic Accessories & SuppliesAdd to cartSpecificationModel:485622Voltage:63VCapacitance:10000UFTemperature:105→Diameter:30mm / 1.1 inchHeight:50 mm / 2 inchFeaturesLong life, high temperatureHigh-frequency capacitorsPackage included20 x Electrolytic Capacitor
Reviews
There are no reviews yet.