DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
3pcs 2x50W TPA3116 AUX+Bluetooth 5.0 HIFI High Power Digital Amplifier Stereo Board AMP Amplificador Home theater without Shell
$54.90Amplifier BoardAdd to cartSpecificationsAudio input:AUX+bluetoothWork voltage:9-24 DCPower:2*50WCooling fin:LargeSpeaker:4-8Ω;30-200WProtection:Overvoltage,undervoltageSize:84*52*24mmFeatures1. This product is full of materials, featuring high performance and high performance price, especially for HIFI music power amplifier with high power and high fidelity.2. TPA3116D2 is a type D amplifier IC launched by TI company, which has very high index parameters.The maximum modulation frequency is 1.2MHZ, and the high …
5PCS USB To TTL Debug Serial Port Cable for Raspberry Pi 3B 2B / COM Port
$20.44Raspberry Pi & Orange PiAdd to cartMore info and driver, please !!!Supports WIN XP/WIN7/ WIN8/ WIN10Reference to WIN10, you can !!!NoteNo driver on raspberry pi 3 model bRaspberry Pi main board is not included!Package included5x USB To TTL Debug Serial Port Cable For Raspberry Pi / COM Port
DIY LED Light Kit ONLY for LEGO 60197 Passenger Train Building Block Bricks Lighting
$32.79DIY Electronic KitsAdd to cartSpecificationInterface:USBColor:As the picture shownThe product is just a light kit, not included the model!!!FitmentONLY For LEGO 60197 Passenger Train Building Block Bricks ToyFeaturesEasy to install.LED powered by USB.Make your model more cool.Package Included1 x LED Light Kit(Model Not Included)
5Pcs M5Stack I/O Hub 1 to 6 Expansion Board Grove I/O interface for Blockly Development IoT MEGA328 Module for Arduino
$75.21Converter BoardAdd to cartDescriptionPbHUB, is a expander for singel-bus GROVE PORTB(Black port on M5GO Base). 1-to-6. PortB can be used as GPIO and analog in two data lines connected to GPIO36 and GPIO26 on ESP32. Same as PaHUB, it provides a solution for mutiple device control by PORTB. With PbHUB each of the IO can be configurated to …
10Pcs Green LED Power Symbol Momentary Latching Switch LED Light Push Button SPST
$20.86Electronic Accessories & SuppliesAdd to cart10Pcs Green LED Power Symbol Momentary Latching Switch LED Light Push Button SPSTDecriptionLatching type:Push it– on, push it again — offLED color:GreenSize(H*D):1.4 x 1cm / 0.55inch x 0.39inch (approx)Quantity:10 pcsFunction:MomentaryLED light voltage:3.2VSwitch voltage:12VMaximum operating current:20mAWith led light, with power symbol, light touch switchEasy to use and installNote1. Please check the picture and part number carefully …
10Pcs Green LED Power Symbol Momentary Latching Switch LED Light Push Button SPSTRead More
100Pcs Red Heat Shrink Solder Sleeve Seal Wire Splice Butt Connector AWG 22-18GA
$72.89ConnectorsAdd to cartName:(100) Heat Shrink Solder Sleeve Seal Wire Splice Butt Connector AWG 22-18GA RedMaterial:Tinned CopperColor:RedShrinking Ratio:2:1Working temperature:-55℃~125℃Shrink temperature:80℃Solder melting temperature:138℃Complete solder melting temperature:160℃Cable cross-section:0.5mm-1.0 mmDiameter:3mm/0.12inch(appr.)FeaturesPlacement on Vehicle:Left, Right, Front, Rear.Solder and seal and with advanced waterproof function.Polyolefin tubing in outside and hot melt adhesive in inside.Can be ideal used in marine and automobile applications.Improve pullout strength, …
100Pcs Red Heat Shrink Solder Sleeve Seal Wire Splice Butt Connector AWG 22-18GARead More
Reviews
There are no reviews yet.