DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
CP2102 USB To TTL/Serial Module Downloader
$10.11Converter BoardAdd to cartCJMCU CP2102 USB To TTL/Serial Module UART STC Downloader For Driver Installation Introduction:http://forum.hobbyant.com/forum-topic-56275.html Description CJMCU-CP2102 its highly integrated, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM and asynchronous serial data bus (UART), supports full-featured modem signal without any external USB devices. CJMCU-CP2102 works with other USB-UART adapter circuit similar to the driver through …
24x12x1 inch Aluminum Silicate High Temperature insulation Ceramic Fiber Blankets
$56.69FabricsFibers & TextilesAdd to cartDescription24x12x1 Inch Aluminum Silicate High Temperature Insulation Ceramic Fiber BlanketSpecificationMaterial:Aluminum SilicateSize:61x30x2.5cm / 24 x12 x1 inchClassification temperature:1260 ℃Long-term temperature:1100 ° CThermal conductivity:0.03Applications* Furnace, heating equipment, pipelines and other lining or wall lining insulation* Furnace door, lid, roof and other heat sealing* Chemical, electrical, high-rise building insulation fireFeatures* Seismic heat resistance* Low thermal conductivity and low …
24x12x1 inch Aluminum Silicate High Temperature insulation Ceramic Fiber BlanketsRead More
10pcs EQKIT AMP-1 TDA2822M Power Amplifier Amplify Module DIY Kit Electronic Production for Diy Kit Electronic PCB Board Module
$82.12DIY Electronic KitsAdd to cartDescriptionPackage Name:TDA2822M AmplifierKit Model:AMP-1Working voltage:DC4.5-9VPCB size:51*36mmSpeaker Size:50mmSpeaker Power:0.25WAMP-1 amplifier using TDA2822M acts as amplifier chip, this chip is STMicroelectronics (ST) developed dual-channel monolithic power amplifier IC, usually in the pocket cassette player (WALKMAN), tape recorders and multimedia speaker in for the audio amplifier. Has a simple circuit, good sound quality, wide voltage range and other …
5Pcs PS2 Game Joystick Switch Sensor Module
$10.92Sensor & Detector ModuleAdd to cart5Pcs PS2 Game Joystick Module For Description This is PS2 game joystick module for Lots of robot projects need joystick. This module provides a affordable solution to that. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. …
100W Outdoor Sunpower Foldable Solar Panels Cells Waterproof Fast Charger Solar Panel
$97.19Solar PanelAdd to cartFeatures1. High efficiency, fast charging.2. Small size, super thin, waterproof, easy to operate, wide range of application3. Easy to carry, with a handle.4. It is more than 5% higher than ordinary efficiency.5. Solar energy conversion efficiency:25%Specifications–Output voltage:USB5V + DC18V–Output current:20A, 5.5A–Color:Black–Solar panel type:Monocrystalline silicon–Conversion efficiency:>25%–Output interface:USB–Open Size:680mmx305mm/26.7inx12in–Folding size:170mmx305mm/6.7inx12inPackage Included–1X Soalr Panel–2X Carabiner–1X USB cable
Reviews
There are no reviews yet.