DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
High-speed Isolation USB To TTL Serial Module Power Isolation Optocoupler Isolation
$15.30Converter BoardAdd to cartOverviewOptical isolation USB to TTL Serial Module Equipped with CH340T USB to serial chip, achieved the power and TTL signal isolation,High-speed and stability, it could avoid the damage of USB and computer blue screen or other issues while use the USB to TTLserial port module, due to improper operation or other external impact on the …
High-speed Isolation USB To TTL Serial Module Power Isolation Optocoupler IsolationRead More
3pcs 3.5mm Plug Jack Stereo TRRS Headset Audio Socket Breakout Board Extension Module
$4.46Converter BoardAdd to cartFeaturesName:Audio breakout board1. TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards.2. TRRS stands for “Tip, Ring, Ring, Sleeve, Inch which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground.3. Some devices use the extra conductor for a microphone …
3pcs 3.5mm Plug Jack Stereo TRRS Headset Audio Socket Breakout Board Extension ModuleRead More
6.5×55 Laser Bore Sighter Red Dot Sight 6.5mm x 55 Brass Cartridge Boresighter Caliber
$20.24Laser BoresighterAdd to cartCaution:Avoid direct eye exposure to the laser beam. Laser radiation is emitted from the aperture.SpecificationHousing Material:BrassLaser Type:Red LaserLaser Wavelength:635~655mmMax Output PowerPower Supply:3Pcs LR41 Batteries (NOT Included)Battery Installation:Positive side facing outwards. Look at your button cell battery, you will see inch+inch on the flat side commonly, which means positive. And the other slightly rounded side is …
6.5×55 Laser Bore Sighter Red Dot Sight 6.5mm x 55 Brass Cartridge Boresighter CaliberRead More
AD584 Voltage Reference 2.5V/5V/7.5V/10V High Precision Reference Source for Voltmeter Calibration
$32.36RF amplifierAdd to cartSpecificationInput voltage:15VOutput voltage:2.5V/5V/7.5V/10VAccuracy:0.0001Warn floating:15ppm/→Size:5*5cm(not included SMA)Package included1 x AD584 Voltage Reference 2.5V/5V/7.5V/10V High Precision Reference Source
5pcs LilyPad MCP9700 Temperature Sensor Module
$16.04Sensor & Detector ModuleAdd to cartDescriptionDetecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical …
76M-108M 2-channel FM Transmitter Board Stereo Wireless Audio Transmission Transmitter Module
$33.20Other Module BoardAdd to cartDescriptionTwo-channel stereo FM transmitter moduleWorking voltage:DC 3V-16VWorking current:17mASize:49mm*31mmFunction description2-channel FM stereo transmissionPower-off memory functionworking frequency displayInput volume and transmission frequency are adjustablesupport wide voltage supplyworking current, small emission efficiency, high power supply, durableRestore factory settingsultra low back noiseInstructions for use– Key:short press, frequency reduction, 0.1MHz;+ key:Short press, increase the frequency by 0.1MHz, long press, restore …
80x50x20mm Corrosion Resistant Aluminum Split Body Aluminum Box Enclosure Case for Electronic DIY
$14.16Electronic Accessories & SuppliesAdd to cartFeaturesHeavy gauge extruded aluminum construction | Easier for drilling, soldering, screwing, problem fixing.Excellent electromagnetic shielding performance;Front and back panels and fasteners are included.Heavy gauge extruded aluminum construction.Excellent electromagnetic shielding performance.Built-in grooves for holding circuit board.Corrosion resistant, lightweight.Durable in use.Great for electronic projects, power supply units, student projects and amplifiers, etc.SpecificationMaterial:extruded aluminumColor:blackSize:80x50x20mmPackage Included1 x 80x50x20mm Enclosure …
4000Peak Power inverter DC12V To AC220V Power Converter Car USB Charger inverter Modified Sine Wave
$157.94InvertersAdd to cartPower InverterFeature– The power inverter can convert DC12V to AC220.– Overload, over temperature, short-circuit, low voltage, over voltage protection.– Stable performance and precise output voltage.Built-in cooling fan with low noise.– Comes with a car charger and a pair of crocodile clip, convenient to use.– Perfect for television, DVD player and other household appliances.Specifications– Color:Black– Frequency:50+/-3Hz– …
Reviews
There are no reviews yet.