US-100 Ultrasonic Ranging Module with Temperature Compensated Sensor Dual Mode Serial Port
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Characteristic
The US-100 ultrasonic ranging module can provide 2cm-450cm non-contact distance sensing function, wide working voltage, self-contained temperature sensor to correct the ranging result, and also has GPIO, serial port and other communication methods. The dog is stable and reliable.
The module includes a transmitter, receiver and control circuit, which is a piezoelectric sensor that is fabricated using electrostrictive phenomena.
An alternating voltage is applied to the piezoelectric material slice (such as quartz crystal, piezoelectric ceramic, lead bismuth titanate, etc.) to cause it to generate electrostrictive vibration to generate ultrasonic waves. The resonance is generated when the frequency of the applied alternating voltage is equal to the natural frequency of the wafer, and the ultrasonic wave generated at this time is the strongest.
Piezoelectric ultrasonic receivers generally operate using the inverse effect of an ultrasonic generator. The structure is basically the same as that of an ultrasonic generator, and sometimes the same transducer is used as both a generator and a receiver.
When the ultrasonic wave acts on the piezoelectric wafer, the wafer is stretched and contracted, and alternating charges are generated at the two interfaces of the wafer, and then converted into a voltage and amplified to be sent to the measuring circuit, and finally recorded or displayed.
Electrical parameters:US-100 ultrasonic ranging module
Operating Voltage:DC 2.4V~5.5V
Quiescent Current:2mA
Operating temperature:-20~+70 degrees
output method:Level or UART (jumper cap selection)
Induction angle:Less than 15 degrees
Detection distance:2cm-450cm
Detection accuracy:0.3cm+1%
Serial port configuration in UART mode:The baud rate is 9600, the start bit is 1 bit, the stop bit is 1 bit, the data bit is 8 bits, there is no parity, no flow control.
Pin 1:Connect to VCC power supply (DC 2.4V-5.5V).
Pin 2:When it is in UART mode, it is connected to the TX terminal of the external circuit UART; when it is in the level trigger mode, it is connected to the Trig terminal of the external circuit.
Pin 3:When in UART mode, connect to RX terminal of external circuit UART; when it is level trigger mode, connect to Echo terminal of external circuit.
Pin 4/5:Connect the ground of the external circuit, and the two pins are turned on.
Level-triggered ranging works
Before powering up the module, first remove the jumper cap on the mode selection jumper to put the module in level trigger mode.
It can be seen from the figure that only a high level of 10US or more is required to be input to the Trig/TX pin, and the system can send eight 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. In this mode, the module converts the distance value to twice the time value at 340m/s, outputs a high level through the Echo terminal, and simultaneously starts the timer, and can read the timer when the port goes low. The value of the high level is the time from the transmission to the return of the ultrasonic wave. The distance value can be calculated based on the duration of this high level. That is, the distance value is:(high time *340m/s)/2.
Note:Since the distance value has been temperature corrected, it is no longer necessary to correct the ultrasonic sound speed according to the ambient temperature, that is, the sound speed is 340m/s regardless of the temperature.
Serial port triggering ranging works
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X55 (baud rate 9600) on the Trig/TX pin, the system can send 8 40KHZ ultrasonic pulses and then detect the echo signal. When the echo signal is detected, the module also measures the temperature value, then corrects the ranging result according to the current temperature, and outputs the corrected result through the Echo/RX pin. The output distance value is a total of two bytes, the first byte is the upper 8 bits of the distance (HDate), and the second byte is the lower 8 bits of the distance (LData), in millimeters. That is, the distance value is (HData*256 + LData) mm.
Serial port trigger temperature measurement working principle
Before the module is powered on, first plug in the jumper cap on the mode selection jumper to make the module in serial port trigger mode.
In this mode, only need to input 0X50 (baud rate 9600) on the Trig/TX pin, the system will start the temperature sensor to measure the current temperature, and then output the temperature value through the Echo/RX pin. After measuring the completion temperature, the module will return a byte temperature value (TData), the actual temperature value is TData-45. For example, after sending 0X50 through TX and receiving 0X45 on RX, the temperature value at this time is [69 (0X45 decimal value) -45] = 24 degrees.
Precautions
1. This module should not be connected with power. If you want to have a live connection, first connect the GND terminal of the module first, otherwise it will affect the normal operation of the module.
2. When measuring distance, the area of the measured object is not less than 0.5 square meters and the plane should be flat as much as possible, otherwise the measurement result will be affected.
3. If the test surface is not very regular or when testing a distant object, multiple measurements can be used to correct it.
Package includes
1 x US-100 Ultrasonic Ranging Module
Weight | 0.009 kg |
---|
Customers Also Viewed
OpenMV OpenMV3 4 2 Camera Module M7 H7 LCD Expansion Board Display Screen Module
$50.02Display ScreenAdd to cartnullFeatureThe LCD Shield gives your OpenMV Cam the ability to display what it sees on-the-go while not connected to your computer. It features a 1.8inch 128×160 16-bpp (RGB565) TFT LCD display with a controllable backlight. Your OpenMV Cam’s firmware has built-in support for controlling the LCD Shield using the LCD module.ApplicationsThe LCD Shield is great …
OpenMV OpenMV3 4 2 Camera Module M7 H7 LCD Expansion Board Display Screen ModuleRead More
3pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P Socket
$10.96Sensor & Detector ModuleAdd to cartIntroduction to the RFID moduleThe MF522-AN module adopts MFRC522 original chip design card reader circuit, which is easy to use and low in cost. It is suitable for users of advanced applications such as device development and card reader development, and users who need to design/produce RF card terminals. This module can be directly loaded …
3pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P SocketRead More
Transparent Acrylic Sheet Housing Module Case for DSO138 Oscilloscope
$17.48DIY Electronic KitsAdd to cartFeatureThis product is for DSO138 Oscilloscope only. (Product ID:984002, 969762)Color:TransparentMaterial:AcrylicInstallation size:12.7 x 8.7 x 2.6 (L*W*H)Note:Package does not includes the DSO138 Oscilloscope.Instruction:Click to openPackage includes1 x DSO138 Transparent Acrylic Sheet
20Pcs 3V 650nM 5mW Line Laser Diode Module
$41.34Module ComponentsAdd to cartDescriptionSpot mode:line(Continuous output)Dimensions:diameter 9mm x length 23mmLaser working life:5000-10000 hours or moreLaser wavelength:650nmOutput power:5mWOperating voltage:DC3VWorking current:16mA ~ 20mAWorking temperature:-36 → ~ 65 →Storage temperature:-36 → ~ 65 →Level:sub-industrial gradeColor:red lightMaterial:brassApplication(1) industrial grade:can be used for equipment, health care, military, Kam pseudo security, stage lighting, tools, U disk, mobile phone, projection teaching flip pen, warm measuring …
MMDVM Open-Source Multi-Mode Digital Voice Modem DIY Kit Expansion Board for Raspberry Pi
$103.03Raspberry Pi & Orange PiAdd to cartDescription– This board could cooperate Raspberry Pi , Orange Pi, a variety of school development board to use.– Board has been applied in the GM300 GM3188 3688 950I 338 Vitex DR-1X, other types of repeaters and car stations need to be studied yourself.– The MMDVM is intended to be an open-source Multi-Mode Digital Voice Modem,which …
MMDVM Open-Source Multi-Mode Digital Voice Modem DIY Kit Expansion Board for Raspberry PiRead More
3Pcs 5V-30V DC PWM Speed Controller Mini Electrical Motor Control Switch LED Dimmer Module
$10.04Other Module BoardAdd to cartFeaturePWM DC motor speed controller is a very safe product.When the situation is overcurrent, it will disconnect by itself. after cooling off a few seconds, the fuse will recovery automatically.With high voltage and high current resettable fuseMini but usefulSpecificationOperating voltage:DC 5-30VControl power:90W (maximum)Quiescent current:0.015A (standby)PWM duty cycle:1% -100%PWM frequency:10khzSize:29mm*23mm (excluding handles)Total height:15mmKnob color:Send randomlyPackage included3 …
3Pcs 5V-30V DC PWM Speed Controller Mini Electrical Motor Control Switch LED Dimmer ModuleRead More
Reviews
There are no reviews yet.