5Pcs DIY Touch Vibration Alarm Kit Electronic Training Teaching
$18.35
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Working principle
The touching vibration alarm consists of touch trigger circuit, vibration trigger circuit and alarm circuit. The 555 time base circuit U1 forms the typical monostable operating mode. The transient time is determined by the values of RP1, R2 and C2.
Usually the circuit is in steady state, 555 time base circuit 3 pin output low, the alarm chip does not alarm because there is no power supply. When the human touch the electrode sheet M, the human body induced by the clutter of the signal injected into the 555 trigger pin 2 through C1, or vibration sensor S1 connect instantly because of the vibration, will both cause the U1’s pin 2 to appear instantly low level , So that the 555 circuit flip into the transient, pin 3 mutate to high level, alarm chip works.
Transient time is over, the time base circuit back to steady state, stop the alarm. The length of the alarm time can be adjusted by changing RP1. LED is a two-color light-emitting diodes, green LED bright after power, use as the power indicator light, the red and green light are bright and shows the overall orange when alarming, the resistance of resistor R5 determines the alarm sound play speed, generally take 180K-240K, pay attention to install the resistor before installing the chip, the entire circuit can work under DC 3-6V.
Note
Battery is not included.
Package included
5 x DIY Touch Vibration Alarm Kit
Weight | 0.065 kg |
---|
Customers Also Viewed
Earphone in Line Volume Control Cable Audio Stereo Extension Adapter
$16.19Switch AccessoriesAdd to cartDescriptionsEarphone In-Line Volume Control Cable Audio Stereo Extension Adapter3.5mm Earphone / HeadphoneIn-Line Volume Control AdapterCompact Designed Connectors3.5mm Jack Headphone Plug to Straight Female SocketIn-Line Volume Control for all headphones with a 3.5mm plugCable Length:1.2 MetersFeaturesAn in-line volume control allows you to adjust volume from audio player to your earphone or headphone.It features a 3.5mm stereo …
Earphone in Line Volume Control Cable Audio Stereo Extension AdapterRead More
Transparent Acrylic Sheet Housing Case for DSP & PLL Digital Stereo FM Radio Receiver Module
$10.92Other Module BoardAdd to cartFeatureThis product is for DSP & PLL Digital Stereo FM Radio Receiver Module 87-108MHz With Serial Control only. (Product ID:1004778)Color:TransparentMaterial:AcrylicPackage included1 x Transparent Acrylic Sheet Housing Case
20pcs Blue Male USB 2.0A To Mini Male USB B Power Data Cable for Nano V3.0 ATMEGA328P Module Board
$33.08Module ComponentsAdd to cartFeaturesStandard:Hi-Speed USB 2.0 (480 megabits per second) Connectors:Male USB 2.0A To Mini Male USB BCompatible with mobile phone,table PC,camera,etcColor:BlueLength:1FT/30CMPackage Included20 x 30CM Blue Male USB 2.0A To Mini Male USB B Cable
2Pcs 350W 2 Ways Crossover Audio Board Tweeter Bass Speaker Frequency Divider 2 Unit for 4-8Ohm DIY Speaker Filter 2800Hz
$76.53Amplifier BoardAdd to cartDescriptionThe frequency divider is suitable for a high-pitched mid-range two-bass speaker, or a single-bass low-middle speaker. The speaker is suitable for 4-8 ohms impedance. The design is based on the 4-8 ohms mass value design. Most products are the same, in order to improve the sound quality. SpecificationsSize:120(L)x77(W)x37(H)mmFrequency point:2800Hz(that is, the bass works at frequencies …
Reviews
There are no reviews yet.