3Pcs DIY Touch Vibration Alarm Kit Electronic Training Teaching
$11.65
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Working principle
The touching vibration alarm consists of touch trigger circuit, vibration trigger circuit and alarm circuit. The 555 time base circuit U1 forms the typical monostable operating mode. The transient time is determined by the values of RP1, R2 and C2.
Usually the circuit is in steady state, 555 time base circuit 3 pin output low, the alarm chip does not alarm because there is no power supply. When the human touch the electrode sheet M, the human body induced by the clutter of the signal injected into the 555 trigger pin 2 through C1, or vibration sensor S1 connect instantly because of the vibration, will both cause the U1’s pin 2 to appear instantly low level , So that the 555 circuit flip into the transient, pin 3 mutate to high level, alarm chip works.
Transient time is over, the time base circuit back to steady state, stop the alarm. The length of the alarm time can be adjusted by changing RP1. LED is a two-color light-emitting diodes, green LED bright after power, use as the power indicator light, the red and green light are bright and shows the overall orange when alarming, the resistance of resistor R5 determines the alarm sound play speed, generally take 180K-240K, pay attention to install the resistor before installing the chip, the entire circuit can work under DC 3-6V.
Note
Battery is not included.
Package included
3 x DIY Touch Vibration Alarm Kit
Weight | 0.039 kg |
---|
Customers Also Viewed
12V 5.2W 165*210mm Mini Polycrystalline Solar Panel Epoxy Board
$26.57Smart Robot & Solar PanelAdd to cartFeaturesExcellent weak light effectIt is important electric parts for transferring the sun light power into electrical power for your applicationBuild your DIY powered models, solar display , solar light and solar toys, etcSpecifications– Material:Polycrystalline– Type:Epoxy solar panel– Maximum power:5.2 (W)– Working current:0-433mA– Working voltage:12V– Open circuit voltage:13.5V– Short circuit current:0.65A– Size:210*165*3(mm)– Reference weight:130gPackage included1 x …
12V 5.2W 165*210mm Mini Polycrystalline Solar Panel Epoxy BoardRead More
10Pcs RobotDyn TP4056 MicroUSB 18650 Li-Ion Battery Charger Module 1A with Power Connector and Cable
$24.26Battery Protection ModuleAdd to cartFeatureThe Micro-USB Li-Ion Battery Charger is a complete constant current/constant-voltage linear charger for single cell lithium-ion/Lithium Polymer (LiIon/LiPo) batteries. The Charger base on TP4056. The ideally suited for portable applications.And the Li-Ion Battery Charger can work within USB and 5V wall adapter. Other features include current monitor,under voltage lockout, automatic recharge, and two status pin …
10pcs 1 Channel 5v Relay Module High And Low Level Trigger
$23.61Relay ModuleAdd to cartDescriptionMaximum load:AC 250V/10A, DC 30V/10A.The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.Working voltage:5V.Every channel of the module can be set high or low level trigger by jumper.Fault tolerant design, even if the control line is disconnect, the relay will not act.Power indicator (green), 1 relay status indicator (red).The interface design is …
10pcs 1 Channel 5v Relay Module High And Low Level TriggerRead More
3pcs 1.25-36V 5A Constant Current Constant Voltage Lithium Battery Charger Step Down Power Module
$23.15Power Supply ModuleAdd to cartSpecificationsInput:IN + input positive, IN- input negativeOutput way:OUT + output positive, OUT- output negativeInput voltage:4-38VOutput voltage:1.25-36V continuously adjustableOutput current:adjustable, maximum 5AOutput Power:75W maximumWorking temperature:-40 to + 85 →Operating frequency:180KHzConversion efficiency:up to 96%Short circuit protection:Yes (limit current 8A)Overtemperature protection:(automatically shut off the output after overtemperature)Input reverse polarity protection:None, (if necessary, please enter the string into the …
Black Acrylic Case + Aluminum Heat Sink for Raspberry Pi Zero W/V1.3
$6.52Raspberry Pi & Orange PiAdd to cartDescriptionThis is the acrylic case specially made for raspberry pi board , both suitable for zero W and 1.3 version.Acrylic material is beatuful and a little fragile , please install it carefully , which is quite easy .And there is a layer of protective film on the surface of acrylic , so it is not …
Black Acrylic Case + Aluminum Heat Sink for Raspberry Pi Zero W/V1.3Read More
2L Non-Toxic Stainless Steel Enema Bucket Tools Kit Douche 2M Tube Reusable Medical Detox Enema Bucket
$78.96Lab Clamp & StandAdd to cartSpecificationName:2L Stainless Steel Enema Bucket KitMaterial:Stainless SteelType:Enema KitCapacity:2LColor:SilverFunction:Cleaning away Bacteria and Reduces the Risk of InfectionsSize:approx.19.5x13cmEnema Tube Length:1.6mFeatures– Large 2L capacity barrel, and you can adjust the water flow through the water control valve.– The enema bucket is reusable, durable, convenient and safe.– Big capacity can clean and vaginal thoroughly.– Cleaning away bacteria and reducing …
50pcs ULN2003 Stepper Motor Driver Board Test Module
$58.32Driver ModuleAdd to cartDescriptionULN2003 is a high voltage and high current Darlington transistor array products with high current gain, high operating voltage, wide temperature range, with strong load capacity and other characteristics, adapted to the requirements of various types of the high-speed high-power drive system.Features1. Using ULN2003 high-power Darlington chip-driven stepper motor2. Increased output expansion interface.3. A, B, …
50pcs ULN2003 Stepper Motor Driver Board Test ModuleRead More
240W 12V/24V 6-200AH Battery Charger for Lead Storage Battery Auto Charger Jump Starter Power Bank
$99.21AC/DC AdaptersAdd to cartFeatures– High power– Suitable for lead storage battery– Double screens– 8 safety protectionSpecifications– Power:240w– Voltage:12v/24v– Charging range:6-200AH– Size:205x140x222mmPackage included1x Battery charger (EU Plug)
Reviews
There are no reviews yet.