DSTIKE BAD Watch Programmable Watch Atmega32u4 USB Laser VL53L0 Distance Sensor Temperture RTC with 800mAh Battery
$151.66
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
What is it
It is a atmega32u4 development watch with distance sensor, laser, buzzer, RGB LED and RTC inside.
It is pre-flashed with a demo program that can display time, inside temperature (RTC3231’s temperature), and distance.
Push the switch upwards and the watch will detect distance between you and your target. If distance is less than 1m, buzzer will sound ‘B~’ and RGB will turn RED at the same time. The distance sensor can only detect 0-1.2m range.
Push the switch downwards and the laser will be enabled. Push down again and it will turn off the laser.
You can look at the introduction video I made.
Why did you make it
I just wanted to make a cool watch for Arduin beginners. Atmega32u4 could be recognized as a key board for computers. That is why a lot of people use it as a Bad USB. That is also the same reason I use it on this watch. I added a command that can show your computer wifi passwords, so when you connect this watch with a computer a window will jump up and shows all the passwords.
You can change the BadUSB code to do what you want with computer. Just for fun. Do not do bad things.
What makes it special
Bootloader is Arduin Leonardo
Buzzer(Digital Pin 12)
RGB LED(Digital Pin 6)
Laser(Digital Pin 13)
1.3 OLED SH1106(IIC)
SDA(Digital Pin 3)
SCL(Digital Pin 2)
Button Up(Digital Pin 10)
Button Down(Digital Pin 8)
Button Select(Digital Pin 9)
Breakou GPIOs(5V,3V,BAT,GND,GPIO5,SDA,SCL,TXD,RXD,AD0)
VL53L0 Distance Sensor(IIC)
Extremely Accurate DS3231(IIC)
40-70mA power cost(work time depends on your code)
800mAh Li-battery
Indicate charging LED (25%,50%,75%,100%)
Power Switch (Click to turn on, double click to turn off, long click to open highlight LED)
How to program it
Open IDE and select ‘Arduin Leonardo’ in the board option.
Tips
I put all the design files and code on my github. When you try the example code you had better to download libraries into your Arduin IDE first
1.Bad USB
Bad USB code part can only be put at the setup() field. If you put it in the loop() you may have a problem where the computer cannot recognize the watch. You have to re-flash bootloader to fix this problem.
2.PowerKeep
I use IP5306 to power this watch. When IP5306 detect current less than 45mA it will turn off power automatically. So I use a PowerKeep code to simulate every 10 seconds click power button. That will keep ip5306 output power all the time. If you do not add this code, this board may run about 30 seconds and then turn off power automatically.
3.RTC
When you find time does not show correctly, you can flash demo code again. Time will synchronize the same time with your computer.
4.DemoCode
After you figured out how to control each part of this watch you can develop your customized watch! I am sorry I am not very good at software part, if any problem you can inform me at anytime.
Package Inlcuded
1 x DSTIKE BAD Watch Programmable Watch with 800mAh Battery
Weight | 0.24 kg |
---|
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.