3pcs TK-RD09-200S 12V DC 0-200S Adjustable 30A Time Delay Relay Module High Precision Monostable
$20.76
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
>>>Manual:Click here to open
Features
– Using the dedicated time chip NE555 as the main control, the time is accurate and stable;
– This section can be set to one of the following two modes of operation
A—power on immediately, disconnect after the delay arrives, (maintained disconnected until the input is powered off);
B—The power is not activated first, and the delay is reached after the delay is reached (always on until the input is powered off).
The jumper settings on the board allow you to switch between functions A and B. The default is set to A mode.
– Adjust the time with an adjustable resistor. The delay range is 0-5 seconds / 1-45 seconds / 1 second – 200 seconds.
– No external start required, power will automatically enter the delay state;
– Typical design operating voltage is 12V DC.
– Standby power saving, only 3mA current.
– Power protection against reverse protection. The reverse power supply will not work and will not burn the module.
Mode Description
A mode:After the module is connected to the power supply, the red indicator light indicates that the power is on. The relay works immediately and the green indicator light is on. At this time, the normally open and common terminals are switched to the on state (the normally closed terminal is disconnected). After a period of time, the relay is turned off and the green indicator light is off. At this time, the normally open and the common terminal are switched to the off state (the normally closed terminal is turned on). Keep this state until the input is powered off.
B mode:After the module is connected to the power supply, the red indicator light indicates that the power is on. The relay does not move, the green indicator light does not illuminate, and the normally open and the common terminal remain in the off state before the power is turned on (the normally closed terminal is turned on). After a period of time, the relay is turned on and the green indicator light is on. At this time, the normally open and the common terminal are switched to the on state (the normally closed terminal is disconnected). Keep this state until the input is powered off.
Package Included
3 x TK-RD09-200S 12V DC 0-200S Adjustable 30A Time Delay Relay Module
Weight | 0.12 kg |
---|
Customers Also Viewed
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water Heater
$21.87Laboratory Heating EquipmentsAdd to cartDC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterSpecificationsModel:SSG-2Type:Normally ClosedMaterials:Plastic & CopperDimension:83*90*49cmPipe Inside Diameter:1/2 inchNet Weight:(approx.) 190gFeaturesThis is a DC12V solenoid valve usually used for solar water heater.It can work with water from 1 to 100℃ (or some other liquid).Working Voltage Range:Rated Voltage ±10%Working Water Pressure:0.02 to 0.8MpaThe working water pressure would be too low/high to …
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterRead More
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set Kit
$76.17Terminal BlocksAdd to cartDescription650 Pcs Assorted Ring Insulated Electrical Wire Terminals Crimp Connector Set KitSpecificationQuantity:650PcsMaterial:Copper + PVC+ TinplateInsulated crimp terminals.All are enclosed in plastic case for easy access.The assorted crimp terminals is including50 x Ring M3 Red50 x Ring M4 Red50 x Ring M5 Red50 x Ring M6 Red50 x Ring M8 Red50 x Ring M4 Blue50 x …
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set KitRead More
3.5 inch Protective Enclosure Case Support Dispaly Screen or Cooling Fan for Raspberry Pi
$9.26Raspberry Pi & Orange PiAdd to cartFeatures– Fully updated for Raspberry Pi 3B+/3B/2B– Can support 3.5 inch screen or cooling fan (notes:can not assemble them at the same time)– Heat sink openings for both CPU and LAN chip– High-gloss finish, surface mountableSpecificationsColor:BlackMaterial:ABSSuitable for Raspberry Pi 3B+/3B/2BWeight:45gSize:9cm*6.2cm*3.4cmPackage Included1x ABS Case4x Non-slip mat4x Screws
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module for
$47.25DIY Electronic KitsAdd to cartDescription1. Use TM1650 (compatible with AIP650) digital tube driver chip, support 8-level brightness adjustment, working voltage 3.3V ~ 5.5V2. IIC interface, only need 2 ordinary IO can drive, do not need to repeat scanning of MCU, saving MCU resources.3. 4 digit 0.56 inch red common negative digital tube with decimal point.4. 0.56 inch with four …
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module forRead More
WEAH-81 Car Heavy Bass Frequency Divider High and Low 2-way 2 Bass Crossover Upgrade Tool
$33.09Amplifier BoardAdd to cartFeatureBrand:WEAHModel:81Power:100WApplicable impedance:4-8ohmFrequency response:100Hz ~ 45HzDimensions:133 x 95 x 44mmApplication environment:Car or home speaker DIYPackage includes1 x Bass Frequency DividerHow to Wire:
5pcs 8-36W intelligent Sensor LED Ceiling Light And Sound Control Power Supply Module Bulb Panel Light Built-in Power Driver
$21.42Power Supply ModuleAdd to cartDescriptionInput Voltage:AC185-265VOutput Current:0.22AOutput Voltage:24-108VEfficiency:90%Working Frequency:50/60HZOutput Power:8-24WSound Control:50-75dBLight control:7-20LuxDiameter:25.8mmFeature1. The combination of sound and light control, when the light is strong, does not work, the light intensity is lower than 12-15LUX, and the sound of the induction 27-36DB starts automatically.2. Delay 40-60S automatically extinguished, easy to install, compatible with ordinary switches, no additional wiring.3. Single trigger, …
Reviews
There are no reviews yet.