3Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$18.14
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
3 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.054 kg |
---|
Customers Also Viewed
3Pcs MPR121-Breakout-v12 Proximity Capacitive Touch Sensor Controller Keyboard Development Board
$16.16Motherboard & Development BoardAdd to cartDescriptionThis is a breakout board for Freescale’s MPR121QR2. The MPR121 is a capacitive touch sensor controller driven by an I2C interface.The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode. The MPR121 also features eight LED driving pins. When these pins are not configured as electrodes, they may be …
220V 100A Class A Power Amplifier Soft Start Delay Temperature Protection Board with Gas Discharge Tube
$24.95Relay ModuleAdd to cartFeatures100% Brand new and high quality.FunctionThe board is equipped with a gas discharge tube. The gas discharge tube is composed of a pair of cold cathode plates which are separated from each other and enclosed in a ceramic tube filled with a certain inert gas (Ar).The gas discharge tube is turned off under normal operating …
Excellway Terminals 40 Pcs 2p 3p 4p 5pin Right angle JST-XH Male Female Lipo Balance Connector
$36.44ConnectorsAdd to cartSpecificaiton Brand:Excellway Pitch:2.54mm Current Rating:1A AC, DC Voltage Rating:125V AC, DC Temperature Range:-25 deg C ~ +85 deg C Insulation Resistance:100M Omega Min. Wire Range:AWG 24~ 32 Insulation O.D.:1.00mm ( Max.) Withstanding Voltage:500V AC/minute Features These work great with all your typical and breadboard style pin connectors and sockets. This kit comes with the most …
HBV-1466FF Fixed Focus 5MP OV5640 FPC Camera Module USB 5 Million Pixels IP Camera Module
$42.85Other Module BoardAdd to cartSpecificationsModel No.:HBVCAM-1466FFModel Size:68.2mm ≠ 26mm ≠ 6mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinitResolution:800LW/PH (Center)Interface:USB 2.0Power:USB bus powerMaximum Power consumption:940 mWPackage:Anti-electrostatic trayOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvcCertifications:FCC and CEActive Array Size:2592*1944Sensor:OV5640 (1/4” )Sensitivity:600mv /(lux-sec)Pixel Size:1.4┢m x1.4┢mMaximum Image Transfer Rate:MJPEG 1024×768 30FPS / YUY2 160×120 30FPSMJPEG 1280×720 …
HBV-1466FF Fixed Focus 5MP OV5640 FPC Camera Module USB 5 Million Pixels IP Camera ModuleRead More
10pcs 40x40mm Small Fan 4010S Computer Chassis CPU Fan 2 Line with Plug
$19.84Electronic Accessories & SuppliesAdd to cartDescriptionAppearance size:40mm x 40mm x 10mmSpeed reference:4000 ± 10% RPMNoise Reference:18DBAir volume reference:18.17-25.97CFMRated voltage:12VRated current:0.10APackage included10 x Fan
Reviews
There are no reviews yet.