10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
5pcs DC 1.8V To 3.6V DIY 76MHz To 108MHz Wireless Stereo PCB FM Radio Module Learning Kits
$28.23DIY Electronic KitsAdd to cartParameterWorking voltage:DC 1.8V-3.6VFrequency range:FM 76-108MHz16-pin dual flat packagePurpose1. Learning electronics.2. Practical ability.3. Particularly suitable for use epoxy PCB welding students use rather than for general use paper-based board.Feature1. FM radio program has a rich, good sound quality, etc.2. It also has search tuning circuit, the signal detection circuit, a mute circuit and compression frequency offset …
5pcs DC 1.8V To 3.6V DIY 76MHz To 108MHz Wireless Stereo PCB FM Radio Module Learning KitsRead More
AK-DB32B-PRO 32-bit Sound-controlled Music Level Light-PRO Version High Sensitivity MIC Signal Acquisition
$73.35LED BoardAdd to cartSpecificationsModel:AK-DB32B-PROInput:5V/250MA (Over 5V may damage the light board. The current can be greater than 250ma, there is no fixed upper limit)Some power supplies have fast charge and high voltage output function, please do not use this kind of chargerOutput:about 2.5WInput port:MicroUSBDimensions:181*16*18.8mmNet weight:86gMaterial:One-piece molding, AnodizingFeaturesBuilt-in highly sensitive microphone (sound-controlled).Aluminum alloy integrated molding housingCustomize LED lighting mold …
5pcs 2S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5V
$26.35Power Supply ModuleAdd to cartDescriptions2-Cell(2S) VersionInput voltage:DC 4.5V-5.5V(Recommend DC 5V)Charging voltage about:2.7V-3.4VCharging current about:230mA-240mAUSB power protectionShort circuit protection and zero volt battery activationBattery protectionOperating ambient temperature:-40° to +85°Storage temperature:-65° to +125°Size:30x 15 x 4mmNoteThe output voltage cannot be measured with a multimeter without a battery. But can be observed with an oscilloscope.Applicationskids toys carDigital CamerasSolar chargingBluetooth ApplicationsAudio equipmentDigital CameraElectronic …
5pcs 2S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5VRead More
Digispark Kickstarter Micro Usb Development Board for ATTINY85
$4.64Motherboard & Development BoardAdd to cartFeaturesSupport for the IDE 1.0+ (OSX / Win / Linux)Power via USB or External Source – 5V or 7 -35V (automatic selection)On-board 500ma 5V RegulatorBuilt-in USB(and serial debugging)6 I/O Pins (2 are used for USB only if your program actively communicates over USB otherwise you can use all 6 even if you are programming via …
Digispark Kickstarter Micro Usb Development Board for ATTINY85Read More
5pcs TPA3116D2 TPA3116 Dual Channel Stereo Digital Audio Power Amplifier Board 120W+120W Module XH-M543
$56.00Amplifier BoardAdd to cartSpecificationProduct Name:TPA3116D2 digital amplifier boardProduct Type:XH-M543Amplifier chip:TPA3116D2Power supply voltage:DC 12-26V (24V recommended)Output power:120W * 2 maxChannel:two-channelSignal to noise ratio:100dbSize:92 * 68 * 17mmPre-board IC improving input sensitivity, high-definition sound qualityPower supply DC 12V 50W * 2Power supply DC 24V 120W * 2Note:Red is positive, and Black is negative! Package Included5 x TPA3116D2 2*120W Dual-channel Amplifier …
5Pcs 1.6 inch Transflective TFT LCD Display Module 130X130 Sunlight Visible SPI Serial Port 3.3V 5V for Arduino
$49.11Display ScreenAdd to cartFeatures 1.6-inch color screen, support 65K color display, display rich colors Semi-transparent LCD, superior performance, clearly visible under strong light SPI serial bus, only a few IO can light up the display Onboard 3. 3V/5V power conversion chip, compatible with 3. 3V and 5V voltage levels Operating temperature range is industrial grade (-20-70 C) Military-grade …
10pcs 3 String 12A 12V 18650 Lithium Battery Protection Board
$34.87Other Module BoardAdd to cartParameterWorking current:12ACharging current:12ACharging voltage:12VOvercurrent:30AInternal resistance ≤ 25mΩWorking temperature:-30°C / +80°CWeight:board = 10g / pcsSize:56*45*1.2mm (length*width*height)FeaturesOvercharge, over discharge, short circuit protectionPackage included10 X Lithium battery protection board
Reviews
There are no reviews yet.