10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor Module
$24.62Sensor & Detector ModuleAdd to cart3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor ModuleDescriptionCJMCU-219 module is a with I2C interface Bidirectional current / power monitor integrated circuit (IC), and further expand the energy-saving electronic products TI camp. INA219 with the industry’s highest accuracy and smallest size, not only to monitor the voltage drop across a shunt resistor on …
3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor ModuleRead More
GDCPH 16V83F Super Farah Capacitor Automotive Electronic Rectifier 2.7v500F Screw Hole Large Capacity Capacitor
$90.34Electronic Accessories & SuppliesAdd to cartDescriptionThis product can be used in electronic devices such as:RAM, smart three-meter, motor drive, clock circuit, toys, CMOS power failure protection, digital camera, hand-cranked rechargeable flashlight, PDA and other fields as a backup power supply.SpecificationBrand:GDCPHModel:16V83FCapacity:83FRated voltage:16 VSize:231*35*65mmPitch:7mmPackage included1 x capacitor
5pcs PWM DC Motor Governor 5V-16V 10A Speed Switch LED Dimmer Speed Controller
$22.64Motor PWM Speed ControllerAdd to cartParameterMaximum voltage:16VMinimum voltage:5VContinuous current:10AShort circuit maximum current:20A (less than 10 seconds)Speed control mode:PWM stepless speed regulation, can also be used to adjust the lightControl mode:speed control potentiometer (clockwise open, continue to rotate clockwise from 1% to 99%)Duty cycle:0%-99% (0% position is the leftmost state of the potentiometer).When the current is on, 0.002A (there is no …
5pcs PWM DC Motor Governor 5V-16V 10A Speed Switch LED Dimmer Speed ControllerRead More
3pcs 7W 9W 12W 15W LED Non Isolated Modulation Light External Driver Power Supply AC90-265V Constant Current Thyristor Dimming Module
$17.33Driver ModuleAdd to cartSpecificationsInput voltage:AC90-265VOutput voltage:DC21-48VOutput current:300mA(adjustable)Product size:68*34*22mmWorking temperature:Ta:50 TC:75Efficiency:≥80%Power factor:0.6Product application:spotlight PAR light / bulb light / candle light / etc.Package Included3 x 7W 9W 12W 15W LED Non Isolated Modulation Light External Driver
5Set Mini Emergency Hand-cranked Dynamotor Charger Portable Hand-cranked Generator 3V 5V for Diy Electronic Production with Clip Lines
$37.08Electronic Accessories & SuppliesAdd to cartDescriptionUnderstand the gear’s speed-increasing transmission conversion and the principle of electric energy generation, and cultivate the manual and brain skills, which is very suitable for manual classes in schools or for adults and children to play together!When shaking slowly for one second or more, the generating voltage can easily reach 3V, and it is easy …
APPJ Single End 6J1 + FU32 Tube Amplifier Board Class A Power AMP Hifi Vintage Audio Assembled Board
$182.24Amplifier BoardAdd to cartNew update:The appearance is updated from March 6, 2021.SpecificationsAssembled, solder freeDriver tubes:6J1x2PCSPower tubes:FU32x2PCSPower output:3W+3W @8ohmFrequency response:30-40KHz(+-1dB)Input sensitivity:550mVSignal-to noise-ratio:-80dB/3WInput power:85-264VACPower consumption:40WInput impedance:10K ohmOutput impedance:16ohm,8ohm,6ohm,4ohmPackage dimension:12*21*17cmPackage weigth:1.5KGNoteThe self-made shell must be opened with sufficient heat dissipation holes, preferably 50% of the shell area, at least 30%, otherwise it will affect the service life.Package Included1 x End 6J1 …
Caturda C2707 4Channel I2C interface Current Voltage Power Monitoring Module for Raspberry Pi
$39.03Raspberry Pi & Orange PiAdd to cartSpecificationsCurrent and power monitor for Raspberry Pi, 4 channels, can monitor the current, voltage, power and voltage across the sampling resistor through the I2C/SMBus interfaceFeaturesRaspberry Pi 40pin GPIO Interface, fit for Raspberry Pi all SeriesSupport 4 Channel I2C/SMBus CommunicationOnboard 1ohm 1% Resistance.Monitor 3.2A Bidirectional current12bit ADC Measuring 0-26V VoltageWorking Voltage:3.3V/5VInterface:I2C/SMBusResistance:1ohm 1%Voltage Range:0-26VCurrent:÷3.2ASize:65mmx30mmPackage Included1* Monitoring Module
Reviews
There are no reviews yet.