10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
5x 10x USB 8 LED Lights Handheld Stand Desktop Reading Magnifier
$24.29PhysicsAdd to cart5x 10x USB Eight 8 LED Lights Handheld Stand Desktop Reading Maintenance Multipurpose Magnifier 75RCDescription1. [2 In 1 Design]:It is not only a handheld magnifier, but also a desktop stand magnifier. It can be used as a desk magnifier by pulling its stand and placing it on a table. It can also be folded up …
5x 10x USB 8 LED Lights Handheld Stand Desktop Reading MagnifierRead More
DALY BMS 16S 48V 30A 40A 60A 3.2V 18650 Bluetooth 485 to USB Device NTC UART Software Togther Lion LiFepo4 Battery BMS
$12.14Battery Protection ModuleAdd to cartType 30A com UART BT / Type 30A com UART 485 / Type 30A com UART 485 CAN / Type 40A com UART BT / Type 40A com UART 485 / Type 40A com UART 485 CAN / Type 60A com UART BT / Type 60A com UART 485 / Type 60A com UART 485 CAN / Type USB to CAN box / Type USB to RS485
5Pcs Geekcreit 328P Multifunction Expansion Board V3.0 for NANO UNO
$24.26Expansion Board & ShieldAdd to cartDescriptionThe extension board specifically for the NANO , welding on two rows of pins, can be used in the duemilanove 2009, U N O R1Package included5 x 328P Multifunction Expansion Board V3.0
20pcs LilyPad MCP9700 Temperature Sensor Module
$55.07Sensor & Detector ModuleAdd to cartDescriptionDetecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical …
IO22C04 4 Channel Pro Mini Relay Module Expansion Board Multi-function Delay Relay PLC Power
$24.04Relay ModuleAdd to cart>>>Manual:Click here to openFeatures– Operating voltage:power supply 1,DC 6.5-25V; power supply 2,DC 5V– Operating Current:Standby current (all relays closed) 15mA, 1 relay open 45mA, 2 relays open 77mA, 3 relays open 109mA, 4 relays open 140mA– Size:80x66x19mm– Weight:79g- On-board resources:4x opto-isolated inputs (low level trigger, NPN type), 4x buttons, 1 4 bit digital tube display, …
1-1000M 3W HF FM VHF UHF FM Shortwave Broadband Amplifier Upgrade Improved Version
$30.60Other Module BoardAdd to cartApplicationsBroadband RF power amplification, suitable for HF FM VHF UHF FM transmission of various radio applications, short-wave FM remote control toys, radio walkie-talkies, digital radio stations, etc., can output up to 3 watts, 15V voltage supply, 1MHZ to 1000MHZ can work frequency range.Technical indicators1. The supply voltage Voltage:DC + 12 ~ 15V (typical 15V @ …
1-1000M 3W HF FM VHF UHF FM Shortwave Broadband Amplifier Upgrade Improved VersionRead More
Geekcreit LTDZ 35M-4400M Handheld Simple Spectrum Analyzer Measurement of interphone Signal
$159.96Test & Measuring ModuleAdd to cartNew update version:Update from December, please use the new manual.Introduction:>>>Click here to openThis product uses the local oscillator signal and the external test signal to obtain the difference frequency signal, and calculates the amplitude of the external test signal through the detector. Using a high-precision VCO source, the heterodyne signal frequency can be measured very …
Geekcreit LTDZ 35M-4400M Handheld Simple Spectrum Analyzer Measurement of interphone SignalRead More
Reviews
There are no reviews yet.