10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
M5Stack 8-Way Servo HAT STM32F030F4 Microcontroller Control Board for M5StickC ESP32 IoT Development Board
$16.96Other Module BoardAdd to cartDescription 8Servos HAT is an 8-way servo control board compatible with M5StickC. The brains of the borad is the STM32F030F4 microcontroller which communicates with M5StickC through I2C. In order to ensure that multiple servos can work at the same time, the HAT is equipped with a separate 16340 battery base for an external and independent …
Screw Shield V3 Terminal Expansion Board for UNO R3
$8.73Expansion Board & ShieldAdd to cartScrew Shield V3 Terminal Expansion Board For Compatible UNO R3DescriptionWe use to do work, always feel bad connection on the port. Either use bread plates into line, either using the sensor cable expansion board with Dupont, feel less reliable, and now we launch a terminal expansion board can be directly screwed onto the thread of …
Screw Shield V3 Terminal Expansion Board for UNO R3Read More
CH340G RS232 Upgrade USB to TTL Auto Converter Adapter STC Brush Module
$6.55Converter BoardAdd to cartFeaturesThere are power light PWR, and TXD and RXD indicatorsReserve RTS, CTS location3.3V and 5V dual voltage selectionSupport XP/WIN7/WIN8/WIN10 systemAnti-short-circuit, anti-overcurrent, anti-reverse, anti-high voltage multiple protection.Package includes1 x Module
10pcs CJMCU-8575 PCF8575 Bidirectional IIC I2C And SMBus I/O Expander Expansion Board
$80.46Expansion Board & ShieldAdd to cartDescriptionHave you run out of I/O pins This great IC allows the user to expand up to 16 I/O using only two I/O for control! The PCF8575C is controlled through an I2C interface and features 16-bits of quasi-bidirectional input/output pins.Package included10 x Module
5pcs 30MA 5V 0.15W Mini Solar Panel Epoxy Board
$16.04Smart Robot & Solar PanelAdd to cartSpecifications– Maximum power:0.15 (W)– Working current:0-30MA(Depending on the intensity of sunlight)– Working voltage:5 (V)– System voltage:5.5 (V)– Open circuit voltage:5.5 (V)– Short circuit current:0.05(A)– Dimensions:about 53*30 (mm)– Weight:about 12g– For:DIYer– Quantity:5PcsPackage Included5 x solar panel
20Pcs Keyes Brick Finger Heartbeat Module(Pad hole) with Pin Header Board Analog Signal
$55.28Sensor & Detector ModuleAdd to cartDescriptionThis module is fully compatible with ARDUINO single-chip microcomputer, and its connection port is also compatible with Arduino sensor expansion board. This module mainly includes infrared transmitter and photosensitive receiver. The infrared transmitter is on one side of the finger, and the photosensitive receiver is on the other side of the finger; the photosensitive receiver …
20Pcs Keyes Brick Finger Heartbeat Module(Pad hole) with Pin Header Board Analog SignalRead More
Reviews
There are no reviews yet.