10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger for
$10.15Relay ModuleAdd to cartDescription Maximum load:AC 250V/10A, DC 30V/10A. The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Working voltage is 24V. Every channel of the module can be set up by high jumper or low level trigger. Fault tolerant design, even if the control line is broken, the relay will not act. Power indicator …
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger forRead More
5Pcs CJMCU-3386 MC33186DH1 Automotive Computer Board Idle Speed Throttle Drive Board A H Bridge
$50.91Other Module BoardAdd to cartDescriptionThe 33886 is a monolithic H-Bridge ideal for fractional horsepowerDC-motor and bi-directional thrust solenoid control. The IC incorporatesinternal control logic, charge pump, gate drive, and low RDS(ON) MOSFEToutput circuitry. The 33886 is able to control continuous inductive DC loadcurrents up to 5.0 A. Output loads can be pulse width modulated (PWM-ed)at frequencies up to 10 …
20pcs Light Dependent Resistor LDR 5MM Photoresistor Photoelectric Switch Element Photo Detector 5516
$4.36Module ComponentsAdd to cartSpecificationsModel:5549Voltage(VDC):150Power Consumption(mw):100Ambient Temperature(C):-30~+70Spectral Peak(nm):540Bright Resistance(10Lux)K┯:5-10Response Time(MS):Rise:20 Decline:30Package included20 x Resistor
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USB
$36.44Solar ControllersAdd to cartSpecificationsName:20A 12V/24V LCD Display PWM Solar Panel Charge ControllerModel:C11465Rated voltage:12/24V AUTOCharge current:20ADischarge current:10AMax.PV input power:260W(12V),520W(24V)Max solar input12V battery,the highest 23V24V battery when the highest 46VEqualization:14.2VFloat charge:13.7V (defaul,adjustable)Discharge stop:10.7V(defaul,adjustable)Discharge reconnect:12.6V(defaul,adjustable)Charge reconnect:13VVoltage of open light:Solar panel 8V(Light lights delay)Voltage of close light:Solar panel 8V(Light off delay)USB output:2 way USB output,5V/2A(Max.)Self-consumeOperationg temperature:-35-60℃Color:BlackSize:133.5mmx70mmx35mmFeatureBuild-in industrial micro controller.Big LCD display,all adjustable …
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USBRead More
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for Arduino
$39.35Expansion Board & ShieldAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openWhat do I mainly doArduino is a huge ecosystem. If the Pi interface can be converted to the Arduino standard, it can be connected to a variety of compatible Arduino expansion boards and connected to the Arduino ecosystem to obtain more available resources.I just do this.Basic situationCompatible with …
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for ArduinoRead More
Emakefun DC5V RGB Tricolor Lamp Module 5PIN Anti-reverse Connector Compatible with Lego Jack Fixing
$10.61Sensor & Detector ModuleAdd to cartFeature1. Supply voltage:5V2. Connection method:5PIN anti-reverse connection Dupont line3. Module size:40*22.5mm4. Installation method:M4 screw compatible with Lego jack fixing5. Connection port:PH2.0Package includes1 x RGB Tricolor Lamp Module (the other items are not includes)
Reviews
There are no reviews yet.