10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
1000W 220V Electric Non-Stick Cake Pan Pie Maker Iron Machine Baking Snack Maker for Kids
$74.91Solar CollectorsAdd to cartElectric Non-Stick Cake Machine Baking Snack Maker For Kids 1000w 220vSpecificationsMaterial:Aluminium, PlasticColor:YellowVoltage:220vPower:1000wSize:24*20*9.5cmFeatures– The temperature can’t be set, it’s automatic temperature control design.– It’s easy and very convenient to use, just a few minutes.– The lid is active in order to make the cake more fluffy.Package included1 X Cake Machine
100pcs PFM Control DC-DC 0.9V-5V To USB 5V Boost Step Up Power Supply Module
$99.90Boost & Buck ModuleAdd to cartDescriptionMini PFM ControlOn-board input voltage indicatorHigh conversion efficiency, maximum to 96%Any DC voltage input 0.9V ~ 5V, output 5V DC voltage can be stable, with two AA batteries input to the output current of 500-600MA, single AA battery power supply output current about 200MAOn-board USB female, can supply power directly to the USB interfaceSmall dimensionSpecificationInput …
100pcs PFM Control DC-DC 0.9V-5V To USB 5V Boost Step Up Power Supply ModuleRead More
TPA3116 Subwoofer Amplifier Board 2.1 Channel High Power bluetooth 4.2 Audio Amplifiers DC12V-24V 2*50W+100W Amplificador with Shell
$54.90Amplifier BoardAdd to cartProduct description1. This is a DC-powered 12-24V power supply, using TI’s TPA3116D2 high-performance digital power amplifier chip as the core, one to do parallel bridged bass channel power amplification output, one to do left and right channel power amplification output. support 100W (bass channel) + 50W (left channel) + 50W (right channel) three-channel output.2. Support …
EleksMaker EleksLaser-A3 Pro 5500mW Laser Engraving Machine CNC Laser Printer
$1,239.29Laser Engraving MachineAdd to cartNotice1. Now we all supply the new version of EleksMaker A3-5500 as the pictures shown. (New version means the improved appearance of machine, while you can know what the old version looks like via the first video above.)2. The frame joint is upgraded and will be easier to assemble. (Remove corner joints and add rubber …
EleksMaker EleksLaser-A3 Pro 5500mW Laser Engraving Machine CNC Laser PrinterRead More
10pcs DC 3V-5V 20mA Rain Water Level Sensor Module Detection Liquid Surface Depth Height for Geekcreit for Arduino – products that work with official Arduino boards
$7.60Power Supply ModuleAdd to cartDescriptionWater Sensor water level sensor is an easy-to-use, cost-effective high level/drop recognition sensor, which is obtained by having a series of parallel wires exposed traces measured droplets/water volume in order to determine the water level. Easy to complete water to analog signal conversion and output analog values can be directly read development board of FOR …
3pcs JUWEI 5V 10W 2 Switch USB Aging Discharge Loader 3 Kinds Current Test Load Power Resistor
$13.41Other Module BoardAdd to cartDescriptionRated power:10WVoltage:5VA designed according to the principle of ohm’s law and through the resistor in parallel through a different switch, can produce 3 kinds of resistance of a new USB electronic load resistance discharge, when all the switch opens, is 2.2 ohm/10W, 4.7 ohm/10W, 2 kinds of resistance in parallel at the same time, in …
Reviews
There are no reviews yet.