inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820io
$15.30Converter BoardAdd to cart>>>Manual:Click here to openOverviewUSR-ES1 embeds Wiznet’s W5500 chip, which uses hardware logic gates to implement the transport layer and network layer of the TCP/IP protocol stack (such as TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE, etc.), and integrates The data link layer, physical layer, and 32K bytes of on-chip RAM serve as data transceiving buffers. …
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820ioRead More
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module
$32.04Electronic Accessories & SuppliesAdd to cart40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
EQKIT KM-1 DC 6-12V PWM Motor Speed Controller Kit DIY Motor Speed Regulator Set Stepless Speed Control
$8.73Module KitsAdd to cartSpecificationsModel:KM-1Operating voltage:DC 6-12VPCB board size:40 x 40mmCircuit descriptionKM-1 uses PWM (pulse width modulation) to control the speed of the motor, adjust the pulse width duty ratio, so that the speed from zero to the maximum speed stepless speed regulation. The wider the crest width of the control waveform, the faster the motor speed; on the …
20pcs 63V 10000UF 105 High Frequency Temp Electrolytic Capacitor 30mm x 50mm Long Life
$108.62Electronic Accessories & SuppliesAdd to cartSpecificationModel:485622Voltage:63VCapacitance:10000UFTemperature:105→Diameter:30mm / 1.1 inchHeight:50 mm / 2 inchFeaturesLong life, high temperatureHigh-frequency capacitorsPackage included20 x Electrolytic Capacitor
Reviews
There are no reviews yet.