inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
5065cm Engraving Area Laser Engraving Machine DIY Kit Desktop Laser Cutting Printer-without Laser Module
$356.97Laser Engraving MachineAdd to cart1. Benbox Software & Manual:Click to download2. Assembly Instructions, please check:http://myosuploads3.hobbyant.com/products/20190326/201903260314326550.zipDescriptionThis DIY desktop blue laser engraving machine is ideal for amateurlaser engraving usage with grayscale printing,low-light positioning and freedompositioning functions.It only need you to connect it to the computer,then you canprint any pictures your like with your own creativity.SpecificationsMaterial:stainless steel and acrylicWorking Voltage:DC 12VEngraving Area:65x50cm(maximum)Size:72x63cmControl …
3pcs 0.36 inch DC0V-32V Red LED Digital Display Voltage Meter Voltmeter Reverse Connection Protection
$10.64Test & Measuring ModuleAdd to cartFeature∵ Super high precision∵ Ultra-low startup voltage, red minimum 2.5V, green minimum 2.7V, blue minimum 3.0V. When the power supply voltage is lower than 3.5V, only the brightness is lowered, but the measurement accuracy is not affected.∵ With reverse connection protection, it will not burn.Measuring range:0.00V-32.0VPower supply range:Red DC2.50-32.0V, green DC2.70-32.0V, blue DC3.00-30.0VHighest input:DC32.0V. Note:If …
120A Amplifier Rectifier Filter Supply Power Board High Power Schottky Rectifier Filter Power Supply Board 10000uf 125V
$109.34Other Module BoardAdd to cartSpecification – Power board with double-sided tinplate PCB board, 8 H-itachi 10000uf 125V capacitor, 4 original import disassemble Schottky 30A150V equivalent to 120A bridge heap!– Schottky’s characteristics are fast, small internal resistance (pressure drop naturally low),So the original rectifier than the original power amplifier for the high demand for power.– Input power:Maxmium Double AC 60V(60V-0-60V)– …
8 inch 25W 6V USB Solar Panel Powered Iron Fan Home Cooling Ventilator Camping Laptop Fan
$153.89Solar CollectorsAdd to cartFeaturesThe fan runs when plugged to the solar panel. And it can be used alone by plugged into computer USB port.When plugged to the solar panel, how the fan works depends on the sunlight.When the sunlight is strong, the fan works fast. When the sunshine is not strong enough, the fan may work low or …
8 inch 25W 6V USB Solar Panel Powered Iron Fan Home Cooling Ventilator Camping Laptop FanRead More
10pcs DC 12V 6A 3 String Battery Protection Board Panels Solar Street Lights
$29.51Other Module BoardAdd to cartDescriptionSize:56x45x3mmContinuous working current:Within 6ACharge current:Within 6ABalance charging:YesShort circuit protection:YesFunction:Prevent overcharge, overplay, circuit protectionSuitable assembly:Nominal 3.7V electric core / three stringsPackage Included10 x 12V Battery Protection Board
Practical CPU info 1.6 inch 84×48 Matrix LCD Memory Display Module with Backlight for Raspberry Pi
$20.80Raspberry Pi & Orange PiAdd to cartFeatures∵ 1.6 inch, 84 x 48 pixels matrix LCD∵ Through the Raspberry Pi internal C programming, to Pi running on the CPU occupancy rate and memory occupancy rate display on the LCD screen, be clear at a glance∵ Can be programmed to show what you want to display∵ A backlight jumper back through the software …
Reviews
There are no reviews yet.