inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
LILYGO TTGO T2 ESP32 0.95 OLED SD Card WiFi + bluetooth Module Development Board
$48.10Motherboard & Development BoardAdd to cartDescriptionFor more product information, please visit:https://github.com/LilyGO/TTGO-T2-ESP32Pin diagramPackage included1 x ESP32 T2(This product does not include battery)2 x Pin1 x Power Cable
50Pcs White Plastic for Rotary Taper Potentiometer Hole 6mm Knob
$8.17Electronic Accessories & SuppliesAdd to cartFeaturesPractical and convenient to use.Hat knobs are high quality, suitable stalk (round shaft) potentiometers.Suitable for 0.6cm shaft diameter potentiometer.SpecificationsColor:WhiteMaterial:PlasticQuantity:50 pcsSize:13 x 17mm (D x H)Inner hole diameter:6mmPackage included50 x Potentiometer Knob
BESTEP 1 Channel 5V Low Level Solid State Relay Module with Fuse 250V2A for Auduino
$6.55Relay ModuleAdd to cartDescription1. 5V solid state relay 240V 2A, output with resistance fuse 240V 2A.2. Size:25*34*25 (length * width * height) Net weight:13g3. Input power:5V DC (160MA)4. Input control signal voltage:(0-1.5V state low level relay ON) (2.5-5V state high level relay OFF)5. The blue KF301 terminal is more convenient to connect to the control line.Module interfaceInput sectionDC+:Connect …
BESTEP 1 Channel 5V Low Level Solid State Relay Module with Fuse 250V2A for AuduinoRead More
Liquid Transfer Siphon Pump Hand Gas Oil Water Fish Tank Battery Power Aquarium
$38.46Electrical Pump & ValveAdd to cartDescriptionFree Electric Battery Syphon Powered Pump – This Cordless water pump will move water for you!Just dip the end into the water and press the on switch, and this remarkable lightweight syphon pump will draw water through the pipe and pump it out of the hose.FeaturesIdeal for thousands of uses around the homeEmptying water buttsDraining …
Liquid Transfer Siphon Pump Hand Gas Oil Water Fish Tank Battery Power AquariumRead More
150pcs 1W Metal Film Resistor 1% 470 ohm
$11.53Electronic Accessories & SuppliesAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionPower:1WResistance value:470┯Resistance tolerance:÷1%Package included150 x Resistor
3PCS 315MHz 220V 10A 1CH Channel Wireless Relay Remote Control Switch Receiver
$19.84Relay ModuleAdd to cartSpecification1. Input Voltage:AC85V-AC220V2. RF Frequency:315MHZ3. RF Working mode:Super heterodyne receiver4. Receiver Sensitivity:-107dBm5. Remote Control Distance:>100 meter(In open environment)6. Decoding Way:MCU Software decoding7. Can store the number of remote control:328. Support remote control type:Fixed code, learning code9. Channel:1CH10 .Multiple working modes:(Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched)11. Wiring Method:Fixed wiring terminal12. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC …
3PCS 315MHz 220V 10A 1CH Channel Wireless Relay Remote Control Switch ReceiverRead More
DC 5V Portable USB Rechargeable Water Cooler Cooling Fan Desk Mini Air Conditioner
$34.41Solar CollectorsAdd to cartSpecificationsMode of operation:mechanicalRated power:5WRated voltage:DC5V 1.0AInput voltage:DC 5VInput current:0.5AWind speed:1 meter away from wind speed, greater than 4.0 m / sNoise:less than 36dBWater tank capacity:less than 1 literPower mode:USBBattery:three sections 5Switch type:normal buttonShaking his head:shaking his head up and downTiming function:no timingWind speed gear:1 fileAir supply type:natural windSize:11.5*11*13.5cmSTEPS FOR USAGE1. Unpack and remove the product;2. …
DC 5V Portable USB Rechargeable Water Cooler Cooling Fan Desk Mini Air ConditionerRead More
Reviews
There are no reviews yet.