inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$15.30Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
USB Boost 5V to 1.2V 3.3V 6V 9V 12V 24V Power Supply Module Adjustable Voltage
$10.92Test & Measuring ModuleAdd to cartFeatureInput voltage:3.5V-12VOutput voltage:1.2-24VOutput PowerOutput voltage 1.2V-2V, used within 2WOutput voltage 2V-20V, used within 3WOutput voltage 20V-24V, used within 2.5WOutput power = output voltage x output currentNote:This product is not a high power supply, please use it within the power range.Package includes1 x Power Module
10pcs IR LED infrared Light Board for CCTV Camera Night Vision 30-40M 6*Array LED White 2.5W DC12V
$26.76LED BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Features– High power / Spot Light / Infrared IR LED boards for CCTV cameras night vision.– Driven board & CDS sensor included.– Power supply exceeds DC13V may greatly reduce the LEDs operating …
2500Pcs 2.54mm XH2.54 2p 3p 4 Pin Connector Plug+Straight Needle+Terminal Socket Header Wire Adaptor
$56.09Electronic Accessories & SuppliesAdd to cartDescription2pin = 200 sets3pin = 200 sets4pin = 100 setsPin Connector Terminal:1500 pcs (Please allow 5% deviation)Package included10 x Connector plug kit with box
19PCS DIY Resin Casting Molds Silicone Jewelry Pendant Craft Making Mould Tool
$58.71ConnectorsAdd to cartSpecificationName:Resin Casting MoldsMaterial:SiliconeColor:TransparentFeature-Flexible, resistant to tearing.-Easy to use and clean.-Easy to release.-Durable in use.-Great for jewelry pendant making, earrings, soap making, chocolate making, sugarpaste making.-You can also add some flowers, glitter, colors to make your own art craft gift.Package Included9x Resin Casting Molds (Mold only, NO accessories)10x Wood Sticks
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development Board
$98.40Motherboard & Development BoardAdd to cartDocumentsProduct specification:Click here to openSchematic diagram:Click here to openat_instruction_set_CN_ONLY:Click here to open (If you mind about this, please don’t buy)hardware_info:Click here to openserial_tool:Click here to openFeature:Ca-01 development board characteristics and detailed parametersCommunication system:4GApplicable frequency band:LTE-FDD:B1/B3/B5/B8LTE-TDD:B34/B38/B39/B40/B41General characteristics:3GPP E-UTRA Release 13Band width:1.4/3/5/10/15/20MHZModule size:24.0mm x 24.0mm x 2.3mmPackage method:stamp hole + LGAModule weight:about 2.6gPower supply voltage:3.3V~4.3V, typical value …
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development BoardRead More
Reviews
There are no reviews yet.