Transistor Tester ESR Capacitance Meter Resistance inductance Measuring
$49.09
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Transistor Tester ESR Capacitance Meter Resistance Inductance Measuring
Specifications
Voltage:DC 9V
Current:20mA
Size:80 x 53 x 20mm
Wire length:140mm
Display size:57 x 37mm
Function introduction
1. One key measure operation, time delay automatic power off. Turn off the current only 20mA, to support the operation of the battery.
2. Automatic detection of PNP and NPN bipolar transistor, N, P channel JFET, MOSFET field effect transistor, diode, dual diode, thyristor, resistance, capacitance, inductance.
Automatic detection pin definition.
3. Measurement of the bipolar transistor current amplification factor (B) and the conduction voltage of the emitter junction (Uf). Darlington transistor can be identified by high threshold voltage and high current amplification factor.
4. Can detect the bipolar transistor and MOSFET inside the protective diode and displayed on the screen.
5. Measurement of MOSFET threshold voltage and gate capacitance value.
6. Support for the measurement of two resistors, the potentiometer can also be measured.
If the potentiometer is adjusted to the end of it, the tester can not distinguish between the middle and both ends of the pin.
7. The resolution of the measurement of resistance is 0.1 ohm, the highest measured value of 50M ohm.
8. Capacitance measurement range from 25pf to 100mF (100 thousand UF). Resolution of up to 1 pF, inductance measurement range of 0.01MH-20H, otherwise it will be displayed as a resistance, if the inductance of the DC resistance value is higher than 2100 ohm.
9. Can detect 2UF above the capacitor equivalent series resistance (ESR), with a resolution of 0.01 ohm. This feature is very important for the detection of capacitive performance.
Capacitance test, the VLoss display on the screen is the loss, attenuation of the meaning of this value is greater, the more close to the scrap it! ESR is the impedance, the smaller the value, the better the performance of the capacitor!
10. Two diodes can display the correct direction of the symbol, while showing the positive pressure drop.
11. LED is detected as a diode, and the forward voltage drop is higher than the normal value.
Dual light emitting diode detector for dual diode. Detection at the same time light-emitting diodes will shine.
12. Each test time is about two seconds, only large capacitance and inductance measurement will take a long time
Package includes
1 x Tester
Weight | 0.18 kg |
---|
Customers Also Viewed
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$15.30Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
USB Boost 5V to 1.2V 3.3V 6V 9V 12V 24V Power Supply Module Adjustable Voltage
$10.92Test & Measuring ModuleAdd to cartFeatureInput voltage:3.5V-12VOutput voltage:1.2-24VOutput PowerOutput voltage 1.2V-2V, used within 2WOutput voltage 2V-20V, used within 3WOutput voltage 20V-24V, used within 2.5WOutput power = output voltage x output currentNote:This product is not a high power supply, please use it within the power range.Package includes1 x Power Module
10pcs IR LED infrared Light Board for CCTV Camera Night Vision 30-40M 6*Array LED White 2.5W DC12V
$26.76LED BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Features– High power / Spot Light / Infrared IR LED boards for CCTV cameras night vision.– Driven board & CDS sensor included.– Power supply exceeds DC13V may greatly reduce the LEDs operating …
2500Pcs 2.54mm XH2.54 2p 3p 4 Pin Connector Plug+Straight Needle+Terminal Socket Header Wire Adaptor
$56.09Electronic Accessories & SuppliesAdd to cartDescription2pin = 200 sets3pin = 200 sets4pin = 100 setsPin Connector Terminal:1500 pcs (Please allow 5% deviation)Package included10 x Connector plug kit with box
19PCS DIY Resin Casting Molds Silicone Jewelry Pendant Craft Making Mould Tool
$58.71ConnectorsAdd to cartSpecificationName:Resin Casting MoldsMaterial:SiliconeColor:TransparentFeature-Flexible, resistant to tearing.-Easy to use and clean.-Easy to release.-Durable in use.-Great for jewelry pendant making, earrings, soap making, chocolate making, sugarpaste making.-You can also add some flowers, glitter, colors to make your own art craft gift.Package Included9x Resin Casting Molds (Mold only, NO accessories)10x Wood Sticks
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development Board
$98.40Motherboard & Development BoardAdd to cartDocumentsProduct specification:Click here to openSchematic diagram:Click here to openat_instruction_set_CN_ONLY:Click here to open (If you mind about this, please don’t buy)hardware_info:Click here to openserial_tool:Click here to openFeature:Ca-01 development board characteristics and detailed parametersCommunication system:4GApplicable frequency band:LTE-FDD:B1/B3/B5/B8LTE-TDD:B34/B38/B39/B40/B41General characteristics:3GPP E-UTRA Release 13Band width:1.4/3/5/10/15/20MHZModule size:24.0mm x 24.0mm x 2.3mmPackage method:stamp hole + LGAModule weight:about 2.6gPower supply voltage:3.3V~4.3V, typical value …
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development BoardRead More
Reviews
There are no reviews yet.