100w 3-speed Silent Hot Water Circulation Pump for Household Solar Heater System
$139.71
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Material:Cast Iron
Color:Green+Black
Power:100W, 50Hz
Voltage:220v~240v
Head:6M
Capacity:50L/min
Circulation area:Less than 50㎡
Connector:25mm(Outer diameter)
Plug Type:China National Standard Plug (We will be based on your country to send the corresponding adapter plug)
Features
Low noise ,no leakage
Robust cast iron construction
3-Stall speed adjustment according your own need
The red button facilitates pre-selection of the pump ooutput
Up to 20% less electrical current consumption in comparison to convenientional standard pumps
Widely used in city buildings, suburban villas, houses, water and pressurized with industrial equipment, air conditioning, boilers, solar circulating water, hot water circulating warm and so on.
The main purpose
The pump is suitable for hot and cold water circulation below 100 °C and supercharging, especially the shower is difficult to ignite due to low water pressure or the water pressure is unstable and easy to fire. Installation and use of this pump can completely solve the problem:the household water pressure is too low and supercharged Water supply; solar water heater water supply, boiler hot water circulation pressurization, industrial equipment liquid pressurization cycle, air conditioning and refrigeration system circulating pressurization
Precautions for use
1. After the pump is installed, connect the power supply and try to turn it for a few minutes (check whether the startup is normal), but the idle time should not be too long to prevent the dry running from affecting the life of the ceramic bearing.
2. When using this product in the home, you should pay attention to the exhaust of the pump, or when it is overhauled, the dripping water will prevent moisture on the board and the moisture-prone items.
3. When the product is supplied with water in the heating system, do not touch it with your hands to prevent burns.
4. Before installing the water pump, it should be ensured that the pipeline has no slag. If there are impurities, welding slag, dirt, etc., it will damage the life of the pump.
5. The pump should be installed in a place that is easy to repair or replace later.
6. Pay attention to the direction of water flow when the pump is installed. The direction of the water flow should be consistent with the water flow mark of the pump.
7. If the direction of the junction box hits the wall or the shift switch is not easy to operate during installation,you can loosen the four hex screws on the pump head. Rotate the motor body until the position is required, please be careful not to damage the rubber washer, then re-tighten the screw evenly and check if the seal line leaks.
Package included
1 X Circulating Pump
Weight | 1.857 kg |
---|
Customers Also Viewed
1:2 1-56MHz 200W Balun HAM Shortwave Antenna Balun 50 ohm to 100 ohm Unbalanced Balance
$56.85RF amplifierAdd to cartThe main parameters1. The transformation ratio is 1:22. Input impedance:50 ohms (unbalanced)3. Output impedance:100 ohms (balance) suitable for QUAD ANT antenna4. Frequency range:1-56MHz5. Standing wave:less than 1.56. Power resistance:500w7. Dimensions:outer diameter 50x130mm8. Weight:350 grams9. Comes with epoxy resin plate and 304 stainless steel lifting ring, with two copper noses for connecting the vibrator, convenient for …
1:2 1-56MHz 200W Balun HAM Shortwave Antenna Balun 50 ohm to 100 ohm Unbalanced BalanceRead More
5 Pcs 2.54mm 20 Pins IC Socket Wide DIP Sockets Adapter Solder Type
$3.55Module ComponentsAdd to cartSpecificationColor:blackQuantity:5 pcsNumber of pins:20 Pins (10pins / row x 2 rows)Pin length:2.9mmPitch:2.54mmRow to row distance:7.62mmDimension:25 x 10 x 8mm (L x W x H)Contact termination through holeContact type dual wipe contactPackage included5 x 20 Pins IC Sockets
1Hz-150Khz 3.3V-30V Signal Generator PWM Pulse Frequency Duty Cycle Adjustable Module LCD Display
$22.06Other Module BoardAdd to cartParameter settingsThe module has four independent keys, used to set the frequency and duty cycle, support short press (increase or decrease a unit)and long press (fast increase or decrease), very simple, set the parameters automatically save, power failure Lost.Module parameters1. Working voltage:3.3 ~ 30V;2. Frequency range:1Hz ~ 150KHz;3. Frequency accuracy:the accuracy in each range is …
4 Slots 18650 Battery Holder Plastic Case Storage Box for 4*3.7V 18650 Lithium Battery with 8Pin
$6.55Module ComponentsAdd to cartSpecificationsSupport Model:18650 BatteryShell material:ABS fire, flame retardant, high temperature, color diversity and other materials for choice.Metal spring:carbon steel nickel plating by NCAA salt spray test, stainless steel spring.External:wire, welding pieces, pins, male and female buckle (3.7v button)Terminal:copper nickel platingCorn:nickel plated with coppervPackage Included1 x 4 Slots 18650 Battery Holder Plastic Case Storage Box
Reviews
There are no reviews yet.