TKS-M8 4-40V DC Motor Speed forward and Reverse Controller with Shell 20A Relay P0 Optocoupler Isolation Anti-jamming
$17.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Working voltage:4-40V DC
Module power consumption:0.6W (static 0.1W)
Signal input:active low. The input is the negative of the optocoupler. A signal is considered to be present when the voltage is below 2V.
Response speed:K1 K2 is 20mS, SW1 SW2 is 50mS.
Output current 20A
PCB size:83*46*20mm
Shell size:87*54*59mm
User Manual
K1:Forward signal
K2:Reverse signal
SW1:Forward limit
SW2:Reverse limit
1. Press K1 and the motor will start to rotate immediately until SW1 closes.
2. Press K2 and the motor immediately starts to reverse until SW2 closes and stops.
3. When K2 is pressed during forward rotation, it will switch to reverse immediately. When K1 is pressed during reverse rotation, it will switch to forward rotation immediately.
1. What mode is P0
P0 is self-locking mode. For example, if the external forward switch (K1) is pressed, the motor will immediately rotate forward. At this time, the instant switch will be released and the motor will continue to rotate forward. It will not stop until the reverse signal (K2) or the forward stop signal (SW1) is encountered.
2. What are the requirements for the signal, can I connect the sensor
The signal is active low and can be a three-wire sensor (NPN-NO type). K1 K2 SW1 SW2 is still the specification.
3. What is the input and output voltage
The input voltage range of the TKS-M8 is 4V~40V, but to ensure reliable operation, it is recommended to use it within the range of 6V-36V. This module is wide voltage. The output motor is the same as the input voltage.
4. What is the limit signal
The limit signal can also be referred to as a stop signal. The limit signal is triggered and level enabled. For example, if a short limit signal is encountered during forward rotation, it will stop, even if the limit signal disappears, it will stop. You must re-transmit the signal once again to get forward again.
5. Can drive a large motor
The maximum current of the TKS-M8 at 12V is 20A, and the maximum current is 10A when the voltage is 24V. The maximum drive motor power is generally not more than 80W. It is recommended that the motor’s stall motor be the standard.
7. Can I achieve automatic forward and reverse
The TKS-M8 does not have a timing function, so strictly speaking, it cannot automatically reciprocate. However, with the start switch, the start switch (A), and the end switch (B), it is possible to achieve infinite reciprocating operation between the two points A and B. Connection method:The start switch and the start switch are connected to K1, the end switch is connected to K2, and SW1 SW2 is not connected. Note that all switches are normally open.
Package Included
1 x TKS-M8 P0 4-40V DC Motor Forward and Reverse Controller with Shell
Weight | 0.081 kg |
---|
Customers Also Viewed
5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$16.60DIY Electronic KitsAdd to cartDescriptionThe purpose of the experiment1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);2. Understand the role of understanding resistance, series and parallel resistance;3. Understand the self-locking switch;4. Understand and recognize adjustable resistors and use adjustable resistors;Experimental stepsStep 1:The long leg of the light-emitting diode (LED) is the positive pole, and the …
50pcs Universal PCB Board 7x9cm 2.54mm Hole Pitch DIY Prototype Paper Printed Circuit Board Panel Single Sided Board
$32.93Electronic Accessories & SuppliesAdd to cartFeaturesPremium one side prototype PCB printed circuit board, universal strip breadboard.All holes are plated through, smooth and clear.Sturdy and easy to use, the plated holes are very solid which makes it very easy to solder components on and they can hold up well and handle reasonable heat levels and dwell times.A good assortment of quality …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPM
$340.19Electrical Pump & ValveAdd to cartFeatures-2inch deep well submersible pump, fits in the 2inch well casing.-Patented impeller design provides extended pump life and heavy flow under the severe circumstances.-This pump has a much longer pump life than the all-plastic-bottom-suction pump.-Solid 304 stainless steel body with heavy duty cast iron discharge.-Industrial grade heavy duty, also good for home usage.-Built in 1/2 …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPMRead More
1Hz-150Khz 3.3V-30V Signal Generator PWM Pulse Frequency Duty Cycle Adjustable Module LCD Display
$22.06Other Module BoardAdd to cartParameter settingsThe module has four independent keys, used to set the frequency and duty cycle, support short press (increase or decrease a unit)and long press (fast increase or decrease), very simple, set the parameters automatically save, power failure Lost.Module parameters1. Working voltage:3.3 ~ 30V;2. Frequency range:1Hz ~ 150KHz;3. Frequency accuracy:the accuracy in each range is …
5pcs LCD1602 LCD Shell for 1602 Blue/Yellow And I2C 1602 Blue/Yellow Green Backlight LCD Module Case
$17.73Electronic Accessories & SuppliesAdd to cartDescription Screen size:2.5 inches Material:acrylic Application 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Blue-Backlight-p-978160.htmlrmmds=search 1602 Yellow Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Yellow-Backlight-For–p-978155.htmlrmmds=search I2C 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/IIC-I2C-1602-Blue-Backlight-LCD-Display-Module-For–p-950726.htmlrmmds=search I2C 1602 Yellow Green Backlight LCD Display Module:https://www.hobbyant.com/IICI2C-1602-Yellow-Green-Backlight-LCD-Display-Module-For–p-950728.htmlrmmds=search Package included 5 x LCD1602 LCD shell
Reviews
There are no reviews yet.