JK11S-100S-5V 10A 0-100S Adjustable ON-OFFf Delay Module Timer Cycle Switch infinite Loop Relay Module
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Voltage:5V DC
Quiescent current:8mA
Operating current:95mA
Trigger:passive switch trigger, response time is 0.03 seconds (the trigger terminal can not access the active signal)
Minimum on-off time:0.2 seconds
Load capacity:10A
Output form:normally open + normally closed
Size:70*20*19mm
Features
– Using industrial-grade single-chip microcomputer to control time, high precision and stable performance;
– Two adjustable resistors are used to adjust the time, and the connection duration and the disconnection time can be independently adjusted;
– The external contact is activated, and the timing is started by shorting the self-reset button. It is also possible to start the countdown by shorting the triggers together to achieve power-on;
– The time range is divided into 0-100 seconds.
Basic working principle
Taking the factory standard setting as an example, the red LED will light when the power is turned on, and the relay is in the off state. When shorted at the trigger end, the module green light is on and immediately enters the working state. Triggering again in the working state will stop working.
In the working state, the relay will pass T1 seconds, break T2 seconds, pass T1 seconds, break T2 seconds… infinite loop. T1 T2 is the length of time the user adjusts with an adjustable resistor.
Instructions
– Power access
The module is connected to the power supply according to the correct power supply voltage and polarity. The red line of the power supply terminal is positive and the black line is negative.
– Trigger line access
The two white lines of the trigger end are connected to a switch, and the module can be started by tapping the switch, and then the switch is stopped by tapping the switch. The trigger switch can be a tact switch, a micro switch, an optocoupler C-E terminal, a relay contact, and the like.
– Normal speed and quick mode settings
The OP1 jumper is used to select normal speed and fast mode, and the shipment defaults to normal speed.
– Loop mode and single mode settings
The OP2 jumper is used to select the loop mode and the single mode, and the shipment defaults to the loop mode.
Cycle mode:After starting, the relay is on-off-on-off-disconnect…, and it is cycled according to the set duration;
Single trigger:After starting, the relay is turned on, and the relay is turned off after T1 duration. (After disconnection, the action ends and waits for trigger again)
Precautions
1. The module power supply is not protected against reverse protection, because it is important to remember that the power supply cannot be connected.
2. The trigger terminal can only be connected to the passive switch, not to the voltage signal. Doing so can damage the module.
3. When the resistance load is connected, no special treatment is needed; when the capacitive load is connected, the relay module is easily damaged by electricity. It is recommended to use the AC contactor derated or the contact current of the motor should be considered within 10A.
Package Included
1 x JK11S-5V 100S Delay Adjustable Multi-function Relay Module
Weight | 0.019 kg |
---|
Customers Also Viewed
5pcs DD2712SA 3.5A Mini 5V-27V to 3.7V DC DC Step Down Buck Power Converter Module Voltage Regulator
$22.52Boost & Buck ModuleAdd to cartDescriptionInput voltage:5-27VOutput voltage:5V Maximum output current:2.5AShort time maximum output current:3.5A Quiescent current:about 250uAWorking frequency:900KHz.Working efficiency:77-92% Size:25 x 15 x 6.3 mmOvertemperature shutdown, Under-Voltage Lockout (UVLO), BS-voltage protection, and short circuit protection.Note1. Input voltage can not be greater than the maximum input range.2. Output power can not be greater than the maximum load for a long …
1080P 5MP 160 Fish Eye Surveillance Camera Module for Raspberry Pi with IR Night Vision
$34.43Raspberry Pi & Orange PiAdd to cartFeatures– This is the new version, can replace the infrared lamp or white fill light, the effect is great.– The Raspberry Pi Camera Board Features a 5 million pixels– And also supports 1080p @ 30 fps, 720p @ 60 fps and 640*480p 60/90 video recording.– OmniVision 5647 sensor in a fixed focus module.– The module …
1080P 5MP 160 Fish Eye Surveillance Camera Module for Raspberry Pi with IR Night VisionRead More
STM32H743VIT6 STM32H7 Development Board STM32 System Board M7 Core Board TFT interface with USB Cable
$58.95Motherboard & Development BoardAdd to cart>>>STM32H750VBT6 Manual:Click here to open>>>STM32H743VIT6 Manual:Click here to openhttp://myosuploads3.hobbyant.com/products/20200410/20200410051631STM32H750HAL-1909.rarhttp://myosuploads3.hobbyant.com/products/20200410/20200410020657STM32H743HAL-1909.rarSpecificationsFrequency:400M (M7 core)Package:LQFP100RAM:1024KBFlash:H750VB:128KB H743VI:2048KB (2M)OLED interface – plug and play, support 0.96 inch / 1.3 inch OLED TFT liquid crystal interfaceConnect 1.3 inch HD full color LCDConnect 2.0 inch HD full color LCD Data storage:W25Q64 (QSPI driver)High speed crystal:25MHZLow frequency crystal:32.768KPower + programmable LED lights2 users and …
2.5 inch 60mm LED Turbo Boost Gauge Vacuum Press Pressure Bar Dials Meter for Car Truck
$99.21Switch AccessoriesAdd to cartSpecifications Material:Aluminum+ABS+Acrylic Power:DC(10-15V) 12V Professional Reads Range:-1~2 BAR Light Colour:White + Red Diameter:2.5 Inch /60mm Packing Size:15 x 8 x 11cm Features 270 degree sweep. Illuminated red needle display. LED Backlight display between white and red light are switched by the button. When the pressure alarm, peak light becomes red, the pressure alarm point can …
2.5 inch 60mm LED Turbo Boost Gauge Vacuum Press Pressure Bar Dials Meter for Car TruckRead More
5pcs JDY-16 bluetooth 4.2 Module Low Power High Speed Data Transfer Mode BLE Module
$28.46Other Module BoardAdd to cartDescriptionJDY-16 Version supports(WeChat, APP, Android) Transparent, IO, RTC, PWM and other functions1.BLE high speed transparent transmission supports 8K Bytes rate communication2.Send and receive data without byte limit, support 115200 baud rate often send and receive data3.Support 3 modes of work4.Support(serial port, IO, APP) sleep wake up5.Support Wechat Airsync, Wechat applet and APP communication6.Support 4 channel …
5pcs JDY-16 bluetooth 4.2 Module Low Power High Speed Data Transfer Mode BLE ModuleRead More
Reviews
There are no reviews yet.