XH-W1411 220V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$17.48
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Temperature range:-55- + 120→
Temperature measurement accuracy:± 0.3→
Resolution:0.1→
Temperature range:-19 ~ 99→
Control accuracy:1→
Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probe
Supply voltage:220V
Temperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)
Output Type:10A relay outputs
Size:90*60mm/3.54 Inch*2.36 Inch
Hole size:70*50mm/2.76 Inch*1.96 Inch
Features
– The board and plastic panels fixed column compartment and lock nut
– Connect the power supply according to the drawings and load control line
– By drawing on the chassis opening 70 * 50mm, then tighten the screws after the thermostat embedded Paste Mask
– After power if the temperature in the interval starts immediately output to stop off value
– Start temperature For example, want to control the production of hot water, heated to 60 degrees stop, stop again begin heating to 45 degrees, then the start value should be 45 degrees, 60 degrees is stopped
– Start temperature> stop temperature = cooling mode
– For example, want to control greenhouse cooling, ventilation fans start when higher than 35 degrees, down 32 degrees when you stop, you start value should be set to 35, stop value is set to 32
– SET Function keys / Off button
1. In the boot state press SET 3s can shutdown, shutdown if the power remains off
2. Press SET to power in the off state, after boot if the power remains switched on
3.Short press SET to switch module temperature intermittent operation → → → reservation Power Off Timer (F1-F3 function independently, with the temperature does not matter, do not need to be able to do)
4. Left F-1 intermittent operation mode in minutes start minute, the right to stop minute
5. F-2 hour timer switch to the left, to the right minutes, maximum 99 hours 59 minutes
6. F-3 power appointment hours left, the right minutes, maximum 99 hours 59 minutes
7. Temperature correction:Unplug thermostat hold the SET power plug into the temperature correction function, the screen display –000– can subtract the temperature at temperature before correction on the basis of the maximum range -9.9 to 99,
8.After the calibration is complete:real-time temperature = temperature before correction + correction
9. Press and hold the (Start + -) power-on self-test function into
10.Press and hold (Stop + -) power to restore the factory settings
Reset
1. If errors or confusing settings, press and hold the power button to stop two restore factory settings
2. 88-888-88 display, buzzer flute sound, complete recovery
Package Included
1 x XH-W1411 Smart Electronics LED Digital Thermometer
Weight | 0.054 kg |
---|
Customers Also Viewed
R103C 6GHz 5.8G Broadband Directional Antenna High Gain ads-b UAV Image Transmission Antenna
$30.90RF amplifierAdd to cartDescriptionThis directional antenna is suitable for directional radio signal transmission and reception signal source reconnaissance lateral, broadband signal testing, etc.The antenna covers the common frequencies of mobile phone communication, UWB positioning module and Wifi and other radio frequency unitsFrequency range:850MHz-6GHzDimensions:22*15CMPolarization method:linear polarizationRated gain:7dbiReturn loss:10DBPower:5WWeight:110gPackage included1 x Broadband Directional Antenna
3Pcs HY-SRF05 Ultrasonic Distance Sensor Module Measuring Sensor Module
$13.93Sensor & Detector ModuleAdd to cart3Pcs HY-SRF05 Ultrasonic Distance Sensor Module Measuring Sensor ModuleDescriptionThis module performance is stable, measure the distance accurately. Module precision, blind spots (2cm) super close.SpecificationInput voltage:5V DCQuiescent currentOutput level(high):5VOutput level(low):0VInduction angleDetection distance:2cm – 450cmAccuracy:up to 0.3cmBlind spots:2cmPackage included3 x HY-SRF05 ultrasonic distance sensor module
AC Contactor AC220V Coil 32A 3-Phase 1NO 50/60Hz Motor Starter Relay LC1 D1810
$48.59RelaysAdd to cartDescriptionAC Contactor AC220V Coil 32A 3-Phase 1NO 50/60Hz Motor Starter Relay LC1 D1810Features1.High strength PC flame retardancy,AC220V copper coil.2.A contactor (motor starter) is a high capacity relay that has built-in auxiliary contact to work with momentary push buttons.3.It is versatile and is often used to control a motor or as a main power switch, sometimes …
AC Contactor AC220V Coil 32A 3-Phase 1NO 50/60Hz Motor Starter Relay LC1 D1810Read More
BESTEP 1 Channel 5V Low Level Solid State Relay Module with Fuse 250V2A for Auduino
$6.55Relay ModuleAdd to cartDescription1. 5V solid state relay 240V 2A, output with resistance fuse 240V 2A.2. Size:25*34*25 (length * width * height) Net weight:13g3. Input power:5V DC (160MA)4. Input control signal voltage:(0-1.5V state low level relay ON) (2.5-5V state high level relay OFF)5. The blue KF301 terminal is more convenient to connect to the control line.Module interfaceInput sectionDC+:Connect …
BESTEP 1 Channel 5V Low Level Solid State Relay Module with Fuse 250V2A for AuduinoRead More
ZL-7903A Multifunctional Automatic Temperature and Humidity incubator Controller XM-18 100-240V AC with with ZL-SHr05J Sensor
$107.15Test & Measuring ModuleAdd to cart>>>Manual:Click here to openFeatureZL-7903A is an industrial intelligent temperature and humidity controller. Optional external SSR to realize bigger heatingpower rate, and with optional temperature PID control. With touch button and big size LCD display, convenient to operate,easy to set up. Applicable for control of incubator, climate chamber, warehouse, and so on.Main Function1. Ventilation fan control2. …
Reviews
There are no reviews yet.