XH-W1411 12V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$16.02
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Temperature range:-55- + 120→
Temperature measurement accuracy:± 0.3→
Resolution:0.1→
Temperature range:-19 ~ 99→
Control accuracy:1→
Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probe
Supply voltage:12V
Temperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)
Output Type:10A relay outputs
Size:90*60mm/3.54 Inch*2.36 Inch
Hole size:70*50mm/2.76 Inch*1.96 Inch
Features
– The board and plastic panels fixed column compartment and lock nut
– Connect the power supply according to the drawings and load control line
– By drawing on the chassis opening 70 * 50mm, then tighten the screws after the thermostat embedded Paste Mask
– After power if the temperature in the interval starts immediately output to stop off value
– Start temperature For example, want to control the production of hot water, heated to 60 degrees stop, stop again begin heating to 45 degrees, then the start value should be 45 degrees, 60 degrees is stopped
– Start temperature> stop temperature = cooling mode
– For example, want to control greenhouse cooling, ventilation fans start when higher than 35 degrees, down 32 degrees when you stop, you start value should be set to 35, stop value is set to 32
– SET Function keys / Off button
1. In the boot state press SET 3s can shutdown, shutdown if the power remains off
2. Press SET to power in the off state, after boot if the power remains switched on
3.Short press SET to switch module temperature intermittent operation → → → reservation Power Off Timer (F1-F3 function independently, with the temperature does not matter, do not need to be able to do)
4. Left F-1 intermittent operation mode in minutes start minute, the right to stop minute
5. F-2 hour timer switch to the left, to the right minutes, maximum 99 hours 59 minutes
6. F-3 power appointment hours left, the right minutes, maximum 99 hours 59 minutes
7. Temperature correction:Unplug thermostat hold the SET power plug into the temperature correction function, the screen display –000– can subtract the temperature at temperature before correction on the basis of the maximum range -9.9 to 99,
8.After the calibration is complete:real-time temperature = temperature before correction + correction
9. Press and hold the (Start + -) power-on self-test function into
10.Press and hold (Stop + -) power to restore the factory settings
Reset
1. If errors or confusing settings, press and hold the power button to stop two restore factory settings
2. 88-888-88 display, buzzer flute sound, complete recovery
Package Included
1 x XH-W1411 Smart Electronics LED Digital Thermometer
Weight | 0.053 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.