10pcs 2 Channel 5V DC Relay Module Relay Drive Module Control Board
$29.61
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Supply voltage:5VDC
Current:greater than 100mA
Load:250V 10A AC or 30V 10A DC
Dimensions:50.5mm (length) * 38.5mm (width) * 18.5 (height)
Weight:31g
PCB color:black
4 fixing screw holes around the board, hole diameter 3.1mm, easy to install and fix
The relay uses high quality Songle relay, single pole double throw. a common end, a normally open end, and a normally closed end
Optocoupler isolation, good anti-interference
Low level pull-in, high level release. The status indicator is on when the inverter is closed, and the status indicator is off when released.
VCC is the system power supply and JD_VCC is the relay power supply. Plug in the jumper cap
Relay contact capacity 250V10A. Relay output is normally open, normally closed;
Active low. Relay signal input voltage range:0-5V;
VCC system power supply. JD-VCC relay power supply. JD-VCC and VCC are shorted.
Wiring instructions
VCC:system power supply positive
GND:system power supply negative
IN1–IN2:Relay Control Port
(Do not reverse)
Package Included
10 x 2 Channel 5V DC Relay Module
Weight | 0.25 kg |
---|
Customers Also Viewed
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water Heater
$21.87Laboratory Heating EquipmentsAdd to cartDC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterSpecificationsModel:SSG-2Type:Normally ClosedMaterials:Plastic & CopperDimension:83*90*49cmPipe Inside Diameter:1/2 inchNet Weight:(approx.) 190gFeaturesThis is a DC12V solenoid valve usually used for solar water heater.It can work with water from 1 to 100℃ (or some other liquid).Working Voltage Range:Rated Voltage ±10%Working Water Pressure:0.02 to 0.8MpaThe working water pressure would be too low/high to …
DC12V 0.02-0.8MPa Solenoid Valve for Solar Water HeaterRead More
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set Kit
$76.17Terminal BlocksAdd to cartDescription650 Pcs Assorted Ring Insulated Electrical Wire Terminals Crimp Connector Set KitSpecificationQuantity:650PcsMaterial:Copper + PVC+ TinplateInsulated crimp terminals.All are enclosed in plastic case for easy access.The assorted crimp terminals is including50 x Ring M3 Red50 x Ring M4 Red50 x Ring M5 Red50 x Ring M6 Red50 x Ring M8 Red50 x Ring M4 Blue50 x …
650 Pcs Assorted Ring insulated Electrical Wire Terminals Crimp Connector Set KitRead More
3.5 inch Protective Enclosure Case Support Dispaly Screen or Cooling Fan for Raspberry Pi
$9.26Raspberry Pi & Orange PiAdd to cartFeatures– Fully updated for Raspberry Pi 3B+/3B/2B– Can support 3.5 inch screen or cooling fan (notes:can not assemble them at the same time)– Heat sink openings for both CPU and LAN chip– High-gloss finish, surface mountableSpecificationsColor:BlackMaterial:ABSSuitable for Raspberry Pi 3B+/3B/2BWeight:45gSize:9cm*6.2cm*3.4cmPackage Included1x ABS Case4x Non-slip mat4x Screws
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module for
$47.25DIY Electronic KitsAdd to cartDescription1. Use TM1650 (compatible with AIP650) digital tube driver chip, support 8-level brightness adjustment, working voltage 3.3V ~ 5.5V2. IIC interface, only need 2 ordinary IO can drive, do not need to repeat scanning of MCU, saving MCU resources.3. 4 digit 0.56 inch red common negative digital tube with decimal point.4. 0.56 inch with four …
20pcs 0.56 inch Digital Tube DIY Kit TM1650 4-digit LED Digital Tube Display Module forRead More
WEAH-81 Car Heavy Bass Frequency Divider High and Low 2-way 2 Bass Crossover Upgrade Tool
$33.09Amplifier BoardAdd to cartFeatureBrand:WEAHModel:81Power:100WApplicable impedance:4-8ohmFrequency response:100Hz ~ 45HzDimensions:133 x 95 x 44mmApplication environment:Car or home speaker DIYPackage includes1 x Bass Frequency DividerHow to Wire:
5pcs 8-36W intelligent Sensor LED Ceiling Light And Sound Control Power Supply Module Bulb Panel Light Built-in Power Driver
$21.42Power Supply ModuleAdd to cartDescriptionInput Voltage:AC185-265VOutput Current:0.22AOutput Voltage:24-108VEfficiency:90%Working Frequency:50/60HZOutput Power:8-24WSound Control:50-75dBLight control:7-20LuxDiameter:25.8mmFeature1. The combination of sound and light control, when the light is strong, does not work, the light intensity is lower than 12-15LUX, and the sound of the induction 27-36DB starts automatically.2. Delay 40-60S automatically extinguished, easy to install, compatible with ordinary switches, no additional wiring.3. Single trigger, …
Reviews
There are no reviews yet.