W3003 12V/24V/220V Microcomputer Digital Display intelligent Temperature Controller Electronic for Burner Fuel Machine Controller
$15.75
Voltage 12V / Voltage 24V /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Supply voltage:12V/24V/220V
Load power:120/240/1500W
Temperature control range:0-450 °C
Temperature range:0-450 °C
Temperature control accuracy:0.1 °C
Measurement input:k-type thermocouple
Output type:direct output
Output capacity:up to 10A
Mounting aperture:73mm
Aperture:4mm
Size:60*45*31mm
Introduction
Setting parameter table
Code:Description:Setting range:Factory settings
P0:Starting temperature:0-450→:00
P1:Stop temperature:0-450→:00
P2:Temperature correction:-10-10→:0
P3:Delayed start:0-10 min:0
– P0 sets the starting temperature
Press the setup button to enter the internal menu. The default display is T0. Press the setup button again to set the desired startup temperature via the up and down buttons.
– P1 sets the stop temperature
b Set the button to enter the internal menu, the digital display is P0, switch to P1 through the up and down buttons, press the setting button again, and set the required stop temperature through the up and down buttons.
– P2 set temperature correction
In the same way, enter the internal menu, switch to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons. In the setting, if the detected temperature value is 0.5 °C larger than the actual temperature value, then the calibration temperature to be set is -0.5 °C. If the inspection temperature value is 1 °C smaller than the actual temperature value, the calibration temperature to be set is 1 °C. Temperature + – Correction temperature = actual temperature.
– P3 sets delayed start
In the same way, enter the internal menu, switch to P3 by the up and down keys, press the setting button again, and set the required delay time by the up and down buttons (the unit is minute > delay start is generally used for compressor refrigeration, if needed for refrigerator freezer, This value needs to be set. The value of the compressor back pressure is set to 3-6 minutes. If you are not using it to control the compressor or do not need the delay function, skip this item.
Heating mode setting method
Setting method:starting temperature
Setting method
Press the SET button to enter the internal menu, set the startup temperature by setting the P0 value, and set the stop temperature by setting the P1 value.
Use Cases
Control the water heater, heat it to 50 °C to stop, and the temperature will fall back to 40 °C to start heating again. How to set it
Step 1:Determine the working mode as heating mode, starting temperature
Step 2:Press the SET button to enter the internal menu, select P0 and press the SET button to set the P0 value to 40 °C.
Step 3:Press the SET button to enter the internal menu, select P1 and press the SET button to set the P1 value to 50 °C.
Cooling mode setting mode
Setting method:Start temperature > stop temperature (program automatically determines the working mode is cooling mode)
The setting method is as above.
Note
When setting the heating mode, if you accidentally set the set temperature value upside down, the output indicator will not light, the load will not work. If the above situation occurs after the setting is completed, you can check whether the set temperature value is reversed. .
Package Included
1 x Digital Display Intelligent Temperature Controller
Weight | 0.066 kg |
---|
Customers Also Viewed
5pcs ST-LINK V2 Programmer Emulator Mini STLINK Downloader for STM8 / STM32 MCU Development Board
$45.35Test & Measuring ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description– Only U disk size and compatible with official ST-LINK V2.– Support official firmware upgrade, support all series of STM8 (SWIM interface), STM32(SWD interface).– Two-channel power output 5V / 3.3V and easier …
5pcs Breadboard Power Supply Module Circuit Test 3.3V 5V Switchable
$24.83Power Supply ModuleAdd to cartDescriptionThe size is exactly the same as most bread plates.Small size, suitable for all kinds of experimental equipment.It has the function of current limiting protection.The interface is popular, and the switching voltage can be switched.Input voltage:5VOutput voltage:5V/3.3V switchableOutput current:less than 500mASize:53 x 11mmPackage Included5 x Power Supply Module
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIY
$24.37DIY Electronic KitsAdd to cartSpecificationInput voltage:AC12-15 VSize(L*W*H):6x 4 x 2.5 cm (Finished)FeatureWith power on delay (about 3 seconds) and DC protection (control voltage around 1 V)With LED status display, when the protection light, the normal work time offUsing 15 A large current relayWorking voltage aAC 12 to 15 V, need independent power supply.Package includes3 x Double-sided circuit boards 3 …
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIYRead More
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And Switch
$9.02Power Supply ModuleAdd to cartDescription1. onboard AMS1117-3.3 chip2. onboard DC input voltage range of 4.75 V to 12 V3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test4. the onboard power light, indicating whether the power supply5. 4-way output voltage interface, convenient connection during the test6. The board size:48.5 …
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And SwitchRead More
32Pcs Science Chemical Experiment Demonstration Tools Reagent Alcohol Lamp Full Set Storage Box
$89.79Lab Clamp & StandAdd to cartSpecificationType:Chemical Experiment BoxMaterial:Plastic, GlassFeatures1. High quality materials. Environmentally friendly and durable.2. Deepen understanding:thinking at your own hands can give your child a deeper understanding of knowledge.3. The variety of experimental tools is rich, which can meet different experimental needsPackage IncludedItem:QuantityBlue and Red Cup:2 SetFour Treasure Box:1 PcsAlcohol Lamp:2 PcsDropping Bottle:2 PcsSpray Bottle:1 PcsBule Dropping Bottle:3 …
3Pcs T2310 AC110V 220V Programmable Digital Time Delay Switch Relay T2310 Normally Open Timer Control Module 0-999S/Min/Hour
$32.79Test & Measuring ModuleAdd to cartFeatureIndependent crystal oscillator, more accurate timing1. Convenient direct output wiring2. Add buzzer and audible alarm3. Add pause button to stop urgently5. Start and stop setting mode, provincial conversion, which is more convenient6. Automatically save when power off, run automatically when power on7. Timing units can be set separately, with 36 working combinations8. Timing range:0-999 seconds, …
5pcs 30CM 1M Portable Photosensitive Dry Film for Circuit Photoresist Sheet for Plating Hole Covering Etching for Producing PCB Board
$21.78Electronic Accessories & SuppliesAdd to cartFeaturesUniversal used in producing PCB board, attach on the PCB surface to make it photosensitive.Suitable for electroplating, hole covering and etching.Great hole covering ability.High resolution.Great adaptive capacity to different material.Durable in pH 8.0-8.5 situation.1.5mil dry film fully covers a 0.25inch height hole.Suitable for usual plating bath, no wrinkle or color error.SpecificationWidth:approx. 30 cm/11.81inchLength:approx. 100 cm/39.37inchOperating …
Reviews
There are no reviews yet.