W3003 12V/24V/220V Microcomputer Digital Display intelligent Temperature Controller Electronic for Burner Fuel Machine Controller
$15.75
Voltage 12V / Voltage 24V /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Supply voltage:12V/24V/220V
Load power:120/240/1500W
Temperature control range:0-450 °C
Temperature range:0-450 °C
Temperature control accuracy:0.1 °C
Measurement input:k-type thermocouple
Output type:direct output
Output capacity:up to 10A
Mounting aperture:73mm
Aperture:4mm
Size:60*45*31mm
Introduction
Setting parameter table
Code:Description:Setting range:Factory settings
P0:Starting temperature:0-450→:00
P1:Stop temperature:0-450→:00
P2:Temperature correction:-10-10→:0
P3:Delayed start:0-10 min:0
– P0 sets the starting temperature
Press the setup button to enter the internal menu. The default display is T0. Press the setup button again to set the desired startup temperature via the up and down buttons.
– P1 sets the stop temperature
b Set the button to enter the internal menu, the digital display is P0, switch to P1 through the up and down buttons, press the setting button again, and set the required stop temperature through the up and down buttons.
– P2 set temperature correction
In the same way, enter the internal menu, switch to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons. In the setting, if the detected temperature value is 0.5 °C larger than the actual temperature value, then the calibration temperature to be set is -0.5 °C. If the inspection temperature value is 1 °C smaller than the actual temperature value, the calibration temperature to be set is 1 °C. Temperature + – Correction temperature = actual temperature.
– P3 sets delayed start
In the same way, enter the internal menu, switch to P3 by the up and down keys, press the setting button again, and set the required delay time by the up and down buttons (the unit is minute > delay start is generally used for compressor refrigeration, if needed for refrigerator freezer, This value needs to be set. The value of the compressor back pressure is set to 3-6 minutes. If you are not using it to control the compressor or do not need the delay function, skip this item.
Heating mode setting method
Setting method:starting temperature
Setting method
Press the SET button to enter the internal menu, set the startup temperature by setting the P0 value, and set the stop temperature by setting the P1 value.
Use Cases
Control the water heater, heat it to 50 °C to stop, and the temperature will fall back to 40 °C to start heating again. How to set it
Step 1:Determine the working mode as heating mode, starting temperature
Step 2:Press the SET button to enter the internal menu, select P0 and press the SET button to set the P0 value to 40 °C.
Step 3:Press the SET button to enter the internal menu, select P1 and press the SET button to set the P1 value to 50 °C.
Cooling mode setting mode
Setting method:Start temperature > stop temperature (program automatically determines the working mode is cooling mode)
The setting method is as above.
Note
When setting the heating mode, if you accidentally set the set temperature value upside down, the output indicator will not light, the load will not work. If the above situation occurs after the setting is completed, you can check whether the set temperature value is reversed. .
Package Included
1 x Digital Display Intelligent Temperature Controller
Weight | 0.066 kg |
---|
Customers Also Viewed
5Pcs CP2102 USB To TTL/Serial Module Downloader
$21.98Converter BoardAdd to cart5Pcs CJMCU CP2102 USB To TTL/Serial Module UART STC Downloader For Driver Installation Introduction:http://forum.hobbyant.com/forum-topic-56275.html Description CJMCU-CP2102 its highly integrated, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM and asynchronous serial data bus (UART), supports full-featured modem signal without any external USB devices. CJMCU-CP2102 works with other USB-UART adapter circuit similar to the driver …
10pcs 180 Degree USB 3.0 Type A female Socket Connector SMT Charging Socket Plug Connector
$10.11Terminal BlocksAdd to cartSpecificationsColorBlueRated Current1.5ARated Voltage30VInsertion Force35N MaxDurability3000 Cycles Min Rubber CorePBT / Icp Ul94V-0 Resistance To Voltage500V Ac Min. Insulation Resistance≥1000MΩPull-Out Force10N Min.Initial 8-20N AfterWorking Temperature-20 Degrees To 60 Degrees Contact Impedance≤30mΩTerminalsBrass C2680,Nickel Base,Gold-Plated 1 u,Package included-10pcs X 180Degree Connectors
Dual Servos Knob Serial Port Control Board Futaba MG995 SG90 Steering Gear Debugging Module
$13.11Other Module BoardAdd to cartFeature1. The onboard stable 8-bit MCU is used to generate high-resolution PWM signals with precise control.2. Support manual mode and return to medium mode, switch by button, with mode indicator.3. Support knob adjustment or serial command control in manual mode.4. The serial port command control can use the matching host computer software or connect to …
Dual Servos Knob Serial Port Control Board Futaba MG995 SG90 Steering Gear Debugging ModuleRead More
Keyes Brick Laser Head Sensor Module (pad hole) with Pin Header Board Digital Signal
$4.36Sensor & Detector ModuleAdd to cartDescriptionThis sensor is fully compatible with ARDUI NO single-chip microcomputer, and its connection port is also compatible with Arduino sensor expansion board. It is mainly composed of a laser head, which is composed of a light-emitting tube core, a condenser lens, and a copper adjustable sleeve. After connecting to the power supply, we directly input …
Keyes Brick Laser Head Sensor Module (pad hole) with Pin Header Board Digital SignalRead More
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board without Decoding -105dBm
$10.37Other Module BoardAdd to cartFeatures1. The product is small in size, high in sensitivity and strong in anti-interference ability;2. The same definition as the four-pin pin of RXB12, the usage is the same. The unit price is lower than RXB12 and can be directly replaced.Technical ParametersWorking voltage:DC3~5VTransmission rate:4.80KBPSQuiescent current:6mAReceive sensitivity:-105dBmDimensions:30 * 9 * 5mmWorking temperature:-20 ° C ~ +80 …
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board without Decoding -105dBmRead More
150g Capacity Quartz Silica Melting Crucible Pot for Gold Silver Platinum Refine
$16.19Glassware KitAdd to cart150g Capacity Quartz Silica Melting Crucible Pot For Gold Silver Platinum RefineDescriptionMaterial:quartzCapacity:150gDiameter:43X57mm/1.69inch X2.24inch(ID*OD)Height:20mm/0.79inchDeepth:15mm/0.59inchNet Weight:40gFeatureQuartz silica melting crucibleProduced by modern ceramic processing technologyHigh orrosion resistance and strength,the temperature resistance up to 2800℃/5072FPerfect for gold silver casting and refine usagePackage included1X Quartz Silica Melting Crucible
WXD3-13-2W Precision Potentiometer 470R 470 Ohm Wirewound Multi-Turn Potentiometer
$4.50Module ComponentsAdd to cartSpecificationsResistance range:470┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included1 x Potentiometer
Reviews
There are no reviews yet.