ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
ULN2003 Stepper Motor Driver Board Test Module for AVR SMD
$4.36Driver ModuleAdd to cartDescriptionULN2003 is a high voltage and high current Darlington transistor array products with high current gain, high operating voltage, wide temperature range, with strong load capacity and other characteristics, adapted to the requirements of various types of the high-speed high-power drive system.Features1. Using ULN2003 high-power Darlington chip-driven stepper motor2. Increased output expansion interface.3. A, B, …
ULN2003 Stepper Motor Driver Board Test Module for AVR SMDRead More
3pcs DD40CRTA 2 in 1 Charger Module DC DC Step Down Module Converter DC 6.5-40V to 4.2V 5V Charging Board 9V 12V 24V to 4.2V Regulator
$18.54Power Supply ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.SpecificationsInput voltage 6.5-40VOutput 1:DC 4.2V/0-1A, as battery ChargerOutput 2:DC 5V/0-1A, as 40-6.5V to 5V Step down module Maximum charging current:1000mA Full charge voltage:4.2V÷2%.Led indicator‘OK’ LED is fully charged OR battery failure indicator; …
3 Pcs Sliver Aluminum Alloy Case with Cooling Fan Protective Shell Metal Enclosure fit for Raspberry Pi 4 Model B
$58.52Raspberry Pi & Orange PiAdd to cartThe Raspberry Pi is not included, you could get it here:Raspberry Pi 4 Model BDescriptionThis is a Protective case designed specifically for Raspberry Pi 4 Model BThe product is made of aluminum and it is very strong,high hardness, pressure resistance, strong metallic luster, not easy to rust,it can perfectly protect your motherboard Aluminum alloy material …
Heavy Duty Iron Boxing Punch Bag Wall Bracket Mount Hanging Stand Holder Hanger
$121.49Lab Clamp & StandAdd to cartFeature1. Heavy duty gym-quality Punch Bag wall bracket made from iron added strength and treated with nti-static spray is perfect for in and outdoor training activity!2. Reinforced iron arm protrudes 60CM from wall and can withstand heavy bags up to 800KG with ease.3. Three bolt points, attaches perfectly into brick or block walls.4. Mount this …
Heavy Duty Iron Boxing Punch Bag Wall Bracket Mount Hanging Stand Holder HangerRead More
20pcs DC 5V Step Up Boost Converter Voltage Regulate Power Supply Module Board with Enable ON/OFF
$72.05Boost & Buck ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.SpecificationsWorking frequency:1MHzUp to 94% Efficiency (usually is 75%-91%) Quiescent current:Turn on output 210uA,Turn off output 5uA. Operating temperature:-40~+85 →Storage temperature:-65~+150 →Size:20 x 15 x 6mmWeight:1.5g ProtectionOver current protection(OCP)Over voltage protection(OVP)Short circuit protection(SCP)Over …
Reviews
There are no reviews yet.