ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
5Pcs MQ-7 MQ7 Carbon Monoxide CO Gas Sensor Detection Module
$13.49Sensor & Detector ModuleAdd to cart>>>Manual:Click here to openOverviewSensitive material MQ-7 gas sensors used in clean air, low conductivity tin oxide (SnO2). High-low temperature cycling detection mode (1.5V heating) carbon monoxide detector, conductivity sensor with the increasing concentration of carbon monoxide gas in the air increases,high-temperature (5.0V heating) cleaning cryoadsorption stray gases. Using a simple circuit to change the conductivity, …
5Pcs MQ-7 MQ7 Carbon Monoxide CO Gas Sensor Detection ModuleRead More
Mini DC12V 3M Micro Quiet Motor Submersible Brushless Water Pump
$24.29Electrical Pump & ValveAdd to cartDescriptionMini DC 12V 3M 240L/H Micro Quiet Brushless Motor Submersible Water PumpFeatureBrushless, permanent magnetic rotor, maintenance-free.Stator and circuit board sealed by epoxy resin.The axis is enclosed with static sealing, which can avoid leaking problemsAdopt high performance stainless steel shaft.Amphibious design, able to work either on land or in water.Super long working life (more than 30,000 …
Mini DC12V 3M Micro Quiet Motor Submersible Brushless Water PumpRead More
100-240V Power Adapter Power Supply Adaptor Plugs AU Standard
$16.19AC/DC AdaptersAdd to cartPower Supply Adaptor for Makita Radio BMR100 BMR100W BMR102 BMR105 DMR105SpecificationsInput:AC 100-240V, 50/60HzOutput:DC 12V 1AColor:BlackSize(Approximately):7.8*4.9*3.2cm(approx.)Wire length(Approximately):93cmPlug type:AU PlugFeatures-Voltage Protection-Short Circuit Protection-Current Protection-Sealed for protection against moisture and humidityApplicationFor Makita Radio BMR100 BMR100W BMR102 BMR105 DMR105Package included1 x Adaptor
3pcs BT201 Dual Mode 5.0 Bluetooth Lossless Audio Power Amplifier Board Module TF Card U Disk Ble Spp Serial Port Transparent
$16.31Amplifier BoardAdd to cart>>>Manual:Click here to openOverviewBT201 5.0 Bluetooth module is a 4-in-1 single chip that supports bluetooth, usb flash drive and TF card. The highlight of the chip is that it supports lossless music playback, simple and clear serial port control function, BLE pass-through function and SPP pass-through function.It greatly reduces the development difficulty of embedded bluetooth …
100pcs 30pF 5.08MM 50V Multilayer Monolithic Ceramic Capacitor
$5.09Electronic Accessories & SuppliesAdd to cartDescriptionFrequency characteristics:low frequencyAdjustment method:fixedLead Type:Radial Lead WireTolerance:÷ 10 (%)Pressure resistance:50 (V)Capacity:30pFFeaturesLarge capacity, small size, high reliability,Stable capacity, high temperature and humidity resistance.Applications:Widely used in electronic precision instruments.A variety of small electronic equipment for resonance, wave filtering Package included100 x 30pF capacitor
220V 750W Stainless Steel Deep Well Submersible Screw Pump Water Pump
$546.74Electrical Pump & ValveAdd to cartSpecificationsName:Submersible PumpColor:grayMaterials:stainless steelPower:750WVoltage:220VSize:540*100mmCord Length:18mPump Head/Lift:75m MaxFeatures-Energy-efficient, easy to install, low energy, low noise.-Stainless steel body, strong and durable, not easy to rust.-Stainless steel filter prevents impurities from entering the pump and has a long service life.Package Included1 x Submersible Pump3 x Accessories(distribute the adapter according to your country)
20Pcs Mini DC-DC1.3A Voltage Converter Step Down Module 12V 24V to 5V 3.3V 9V with integrated inductor for 360 RC
$31.43Power Supply ModuleAdd to cartFeaturesThe maximum output current is 1.3A, and it is running within 1A for a long time;Non-isolated DC synchronous rectification with up to 94% conversion efficiencyOne-piece inductor, lower heat than ordinary shielded inductorUniversal, optional output voltage, spot welding directly on the boardOutput with LED indicator for easy and visual indication of voltage outputWith enable (EN) port, …
65x37mm Universal Slotted Frame Rail Floor Jack Guard Adapter Lift Rubber Pad Rubber Mat
$22.67RubbersAdd to cartDescriptionThis rubber pad is suitable for car Jack with 55mm intake.SpecificationType:Rubber Pad Universal Diameter 65×37 With Wide V-GrooveMaterial:RubberColor:BlackDiameter:65mmTotal height:37 mmGroove Top:15mmGroove Bottom:10mmGroove Height:8mmFeatures1. Universally applicable.2. Industrial Quality.3. Very robust (min. 80 Shore).4. Easy install and durable use.5. Great quality and great Fitment.6. Direct Replacement, No Modifications Necessary.FitmentSuitable For Car Jack With 55mm IntakePackage Included1 x …
65x37mm Universal Slotted Frame Rail Floor Jack Guard Adapter Lift Rubber Pad Rubber MatRead More
Reviews
There are no reviews yet.